Ekinex EK-ET2-TP-R Hızlı Başlangıç Kılavuzu - Sayfa 3

Kontrolör Ekinex EK-ET2-TP-R için çevrimiçi göz atın veya pdf Hızlı Başlangıç Kılavuzu indirin. Ekinex EK-ET2-TP-R 8 sayfaları. Room temperature controller with humidity and co2 equivalent regulator

Sayfayı Yazdır

Ekinex EK-ET2-TP-R Hızlı Başlangıç Kılavuzu

two screws (c);

• snap the plate (a);

• snap the rocker (b) to complete the installation.

a) 1-fold plate (square, with 60 x 60 mm window)

b) Rocker

c) Screws (for device)

d) Device

e) Screws (for metallic support)

f) Metallic support

g) Plastic adapter

h) Rectangular frame (not for NF version)

i) Flush-mounting box (not delivered by ekinex

Mounting position

For optimum regulation the device has to be preferably

installed on an internal wall at the height of 1.5 m and at

least 0.3 m far from doors. The device cannot be installed

close to heat sources such as radiators or domestic ap-

pliances or in positions subject to direct sunlight. If neces-

sary, for the regulation may be used a weighted average

between two values selected among the following ones:

value measured by the internal sensor, value measured

by a temperature sensor connected to a device input, va-

lue received via bus by another KNX device (e.g. from

ekinex pushbuttons).

Switching, display and measuring elements

The device is equipped with a programming LED, 8 di-

splaying LEDs with lightguides for feedback status and

3 sensors.

Switching elements

• Pushbutton (13) for switching between the normal and

programming operating mode.

Display elements

• White / red LED (4) for indication of the heating mode

functionality active / heating ON;

• White / blue LED (5) for indication of the cooling mode

functionality active / cooling ON;

• Blue LED (6) for indication of the dehumidification fun-

ctionality ON;

• Green LED (7) for indication of the humidification fun-

ctionality ON;

)

1,50 m

• Red LED (8) for indication that the measured CO

valent exceeds threshold 3;

• Blue LED (9) for indication that the measured CO

valent lies between threshold 2 and 3;

• Blue LED (10) for indication that the measured CO

equivalent lies between threshold 1 and 2;

• Blue LED (11) for indication that the measured CO

equivalent lies below threshold 1;

• Red LED (12) for indication of the active operating

mode (on = programming, off = normal operation).

For measuring purposes the device is provided with:

• a temperature sensor (not visible, positioned behind

the passage 15);

• a relative humidity sensor (14);

• a CO

equivalent air quality sensor (16).

1) Terminal block for KNX bus line

2) Product label

3) Adapter

4) White (heating mode active) or red (heating ON) LED

5) White (cooling mode active) or blue (cooling ON) LED

6) Blue LED (dehumidification ON)

7) Green LED (humidification ON)

8) Red LED (CO

equivalent concentration > threshold 3)

9) Blue LED (CO

eq. concentration between threshold 2 and 3)

10) Blue LED (CO

eq. concentration between threshold 1 and 2)

11) Blue LED (CO

equivalent concentration < threshold 1)

12) Programming LED

13) Programming pushbutton

14) Relative humidity sensor

15) Temperature sensor

16) CO

equivalent sensor

Note. Programming pushbutton and LED are ac-

cessible from the front side of the device. The de-

vice addressing may be easily carried out after the

assembly of the frame, removing the rockers. Once

the addressing has been done, the device configu-

ration can be later downloaded without pressing the

programming pushbutton.

equi-