Ekinex KNX EK-ED2-TP Hızlı Başlangıç Kılavuzu

Kontrolör Ekinex KNX EK-ED2-TP için çevrimiçi göz atın veya pdf Hızlı Başlangıç Kılavuzu indirin. Ekinex KNX EK-ED2-TP 5 sayfaları. Pushbutton

Sayfayı Yazdır

Pushbutton FF series KNX

Codes:

EK-ED2-TP-... (with LED, temperature sensor and

temperature room controller)

EK-E32-TP-... (basic pushbutton)

TP1

KNX device for switching and control of single loads or

groups of loads and room temperature regulation. It has

to be used in KNX installations for control of homes and

buildings.

Description

The ekinex

pushbutton of FF series is a KNX S-mode

device for on/off switching of loads, dimming of lighting

devices, controlling of motor drives or other programma-

ble switching and control functions. The integrated tem-

perature sensor allows the use as a room or zone tem-

perature controller (*). It is equipped with an integrated

KNX bus communication module and is designed for wall

installation on flush-mounting box. Each channel can be

freely configured to carry out 1 or 2 bus functions and

is provided with programmable LED (blue/green or red/

Versions

Device code

LED colours

EK-ED2-TP

blue / green

EK-ED2-TP-RW

red / white

EK-ED2-TP-BG-NF

blue / green

EK-ED2-TP-RW-NF

red / white

EK-ED2-TP-BG-NFW

blue / green

EK-ED2-TP-RW-NFW

red / white

EK-E32-TP

n.a. (*)

EK-E32-TP-NF

n.a. (*)

EK-E32-TP-NFW

n.a. (*)

*) The programmable LEDs, the temperature sensor

and the room temperature control function are available

for EK-ED2-TP-... versions only.

Datasheet STEKED32TP_EN

Mounting

with frame of the

form or flank series

without frame ('NF series)

with black side profile

without frame ('NF series)

with white side profile

with frame of the

form or flank series

without frame ('NF series)

with black side profile

without frame ('NF series)

with white side profile

white) (*) e.g. as a status feedback or orientation night-

light. Pressing a rocker, the device sends on the bus a

telegram, which is received and executed by one or more

KNX actuators depending on the configuration carried

out. The device is powered by the KNX bus line with a

SELV voltage 30 Vdc and does not require auxiliary po-

wer.

Main functional characteristics

• On/off switching of single loads or groups of loads

• Dimming of lighting devices

• Control of motor drives (for roller shutters, blinds, cur-

tains, etc.)

• Room temperature regulation (*)

• Logic functions

• Sending on the bus of values (temperature, bright-

ness, etc.)

• Switching to forced functioning (lock)

• Recalling and saving of scenes

• Measuring of room temperature through integrated

sensors (*)

• Different functions programmable for short pressure /

long pressure of a rocker

• Status feedback or orientation nightlight through 2-co-

lour programmable LEDs (*)

Other characteristics

• Housing in plastic material

• Wall installation in flush mounting box

• Protection degree IP20 (according to EN 60529)

• Classification climatic 3K5 and mechanical 3M2 (accor-

ding to EN 50491-2)

• Pollution degree 2 (according to IEC 60664-1)

• Weight 80 g (with mounting support)

• Dimensions 82 x 79 x 19 mm (WxHxD)

Technical data

• Power supply 30 Vdc from KNX bus line

• Current consumption < 15 mA

• Power from bus < 360 mW

Environmental conditions

• Operating temperature: - 5 ... + 45°C

• Storage temperature: - 25 ... + 55°C

• Transport temperature: - 25 ... + 70°C

• Relative humidity: 95% not condensing

Completed with frame EK-FOQ-... (form)

and square rockers EK-TQQ-...

Completed as 'NF series (without frame)

with square rockers EK-TQQ-...

Completed with frame EK-FLQ-... (flank)

and rectangular rockers EK-TRO-...

Completed as 'NF series (without frame)

with rectangular rockers EK-TRO-...