Ekinex KNX EK-FB1-TP Hızlı Başlangıç Kılavuzu - Sayfa 3

Kontrolör Ekinex KNX EK-FB1-TP için çevrimiçi göz atın veya pdf Hızlı Başlangıç Kılavuzu indirin. Ekinex KNX EK-FB1-TP 4 sayfaları. Binary output 8-fold 10a

Sayfayı Yazdır

Ekinex KNX EK-FB1-TP Hızlı Başlangıç Kılavuzu

Connection of the loads

The connection of the loads is made with screw terminals

located on the upper front of the device.

Characteristics of the terminals

• screw clamping of conductors

• maximum cross section of conductor 2.5 mm² (single-

wire) or 1.5 mm² (multi-wire)

• recommended wire stripping approx. 6 mm

• torque max 0.8 Nm

In case of connection of loads powered at SELV voltage,

it is necessary to leave an output channel unused (cor-

responding to a pair of terminals) between the outputs

connected to loads with different voltages.

Warning! The electrical connection of the device

can be carried out only by qualified personnel. The

incorrect installation may result in electric shock or

fire. Before making the electrical connections, make

sure the power supply has been turned off.

Warning! Sockets controlled via bus must be cle-

arly identified. Controlling loads with mobile installa-

tion (e.g. household appliances connected to mains

sockets) must be planned and realized with a care-

ful evaluation of the risks that may arise in the case

of control without direct visual contact with the load

(remote control). Connecting loads different than

those planned, remote controlling without direct ve-

rification of the current conditions of the connected

load or automatic controlling based on scenes or

time-scheduling can cause serious damage to pe-

ople and objects.

Configuration and commissioning

Configuration and commissioning of the device require

the use of the ETS

(Engineering Tool Software) program

V4 or later releases. These activities must be carried out

according to the design of the building automation system

done by a qualified planner.

Configuration

For the configuration of the device parameters the corre-

sponding application program or the whole ekinex

duct database must be loaded in the ETS program. For

detailed information on configuration options, refer to the

application manual of the device available on the website

www.ekinex.com.

Application

Product

software

code

(## = release)

EK-FB1-TP

APEKFB1TP##.knxprod

Note. The configuration and commissioning of KNX

devices require specialized skills. To acquire these

skills, you should attend the workshops at KNX cer-

tified training centers.

pro-

Communica-

Group

tion objects

adresses

(max nr.)

152

254

Commissioning

For commissioning the device the following activities are

required:

• make the electrical connections as described above;

• turn on the bus power supply;

• switch the device operation to the programming mode

by pressing the programming pushbutton located on

the front side of the housing. In this mode of operation,

the programming LED is turned on;

• download into the device the physical address and the

configuration with the ETS

At the end of the download the operation of the device

automatically returns to normal mode; in this mode the

programming LED is turned off. Now the bus device is

programmed and ready for use.

Dimensions [mm]

144

0FF

EK-FB1-TP

8xD.O. 10A/230Vac

50/60 Hz

bus KNX

Marks

• KNX

• CE: the device complies with the Low Voltage Directi-

ve (2006/95/EC) and the Electromagnetic Compatibility

Directive (2004/108/EC). Tests carried out according

to EN 50491-2:2010, EN 50491-3:2009, EN 50491-4-

1:2012, EN 50491-5-1:2010, EN 50491-5-2:2010, EN

50428:2005 +A1:2007 + A2:2009

Maintenance

The device is maintenance-free. To clean use a dry cloth.

It must be avoided the use of solvents or other aggressive

substances.

Disposal

At the end of its useful life the product

described in this datasheet is classified

as waste from electronic equipment in

accordance with the European Direc-

tive 2002/96/EC (WEEE), and cannot

be disposed together with the munici-

pal undifferentiated solid waste.

Warning! Incorrect disposal of this product may

cause serious damage to the environment and hu-

man health. Please be informed about the correct

disposal procedures for waste collecting and pro-

cessing provided by local authorities.

Documentation

This datasheet refers to the release A1.0 of the ekinex

device EK-FB1-TP, and is available for download at www.

ekinex.com as a PDF (Portable Data Format) file.

File name

STEKFB1TP_EN.pdf

Warnings

• Installation, electrical connection, configuration and

commissioning of the device can only be carried out by

program.

0FF

Device release

Updating

A1.0

03 / 2014