Astera SpotMax AX10 Kullanıcı Kılavuzu

Işık Fikstürü Astera SpotMax AX10 için çevrimiçi göz atın veya pdf Kullanıcı Kılavuzu indirin. Astera SpotMax AX10 2 sayfaları.

Sayfayı Yazdır
SpotMax™
AX10
USER MANUAL
Manual Version: 1.0
Date of Issue: 30/01/14
Controlling the SpotMax™
Set a color or basic e ect through the control pad on the AX10's backside. Press the MENU/COLOR button and use the + and – buttons to display
di erent colors. Con rm with the ENTER button. Press the ENTER/PROG button and use the + and – button to display di erent programs. Con rm
with ENTER button.
Use Astera's ARC1 remote control, point at individual lights and press the desired e ect. Note that the IR sensor is on the AX10 rearside although
IR
the IR signal should bounce of walls and oor.
Astera's remote control and the AsteraTouch tablet can group several lights together, address individual lights or groups of lights and send
complex e ects to all lights in range. For additional information refer to the manual and quick start guide of ARC2 and ARC6 at
RF
www.astera-led.com/downloads.
Connect an ART3 (Wireless DMX Transmitter) to your DMX desk to send wireless DMX signals to the AX10. You can set the AX10s DMX address
on its control pad or send it from a remote control. Additionally, the AX10 can be controlled by CRMX Wireless DMX (from Lumen Radio) and
DMX
W-DMX (from Wireless Solutions). For additional information refer to the ART3 manual at www.astera-led.com/downloads
Key Functions
Di usor Slots
Thumb
Hole
Di usor Clip
ATTACH
The Di usor must be slid into
the Di usor Slots, then pressed
down rmly and clipped in under
the Di usor Clip.
REMOVE
The Di usor Clip should be pressed
in, and the Di usor Sheet should be
lifted out via the thumb hole.
Contents
-SpotMax™
-2x Di usors
-Powercon True1
Power Cord
SpotMax™
-User Manual
AX10
USER MANUAL
Manual Version: 1.0
Date of Issue: 30/01/14
Key Functions
Thumb
Hole
Di usor Clip
The Di usor must be slid into
ATTACH
the Di usor Slots, then pressed
down and clipped in under the
REMOVE
Di usor Clip.
The Di usor Clip should be pressed
in, and the Di usor Sheet should be
lifted out via the thumb hole.
Controlling the SpotMax™
Set a color or basic e ect through the control pad on the AX10's backside. Press the MENU/COLOR button and use the + and – buttons to
display di erent colors. Con rm with the ENTER button. Press the ENTER/PROG button and use the + and – button to display di erent p
rograms. Con rm with ENTER button.
IR
Use Astera's ARC1 remote control, point at individual lights and press the desired e ect. Note that the IR sensor is on the AX10 rearside
although the IR signal should bounce of walls and oor.
Astera's remote control and the AsteraTouch tablet can group several lights together, address individual lights or groups of lights and
RF
send complex e ects to all lights in range. For additional information refer to the manual and quick start guide of ARC2 and ARC6 at
www.astera-led.com/downloads.
Connect an ART3 (Wireless DMX Transmitter) to your DMX desk to send wireless DMX signals to the AX10. You can set the AX10s DMX
DMX
address on its control pad or send it from a remote control. For additional information refer to the ART3 manual at
www.astera-led.com/downloads.
Due to the Powercon True1 cord,
Turn clock-wise to tighten the
the SpotMax™ is IP65 waterproof,
legs of the SpotMax™.
even when charging. Ensure the
rubber caps are closed when not
charging to make it waterproof.
Power In
Power Out
The legs of the SpotMax™ have a U-shaped
enclosure to rest the leg latch into so that
when closed, the legs remain together, and
when open, the legs remain open. When the
legs are closed, the SpotMax™ can be
carried by hand and/or placed neatly into a
transportation case.
RF Antenna
U-Shaped
Enclosure
315°
Leg Latch
Hole for Clamp
Diffusors
Contents
Diffusors
SpotMax
Power Cord
2x Di usors
Manual
SpotMax
Manual
Power Cord
Key Functions
2x Di usors
Contents
What the display indicates
Battery Icon & Status LED
Key Functions
Controlling the SpotMax™
Wide Angle
(30° di usor)
Diffusors
Contents
13° Spot
(without di usor)
(di usor sheet)
Wall Wash
Power In
Di usor Clip
in, and the Di usor Sheet should be
REMOVE
down so that Di usor Clip will
The Di usor must be placed into
when closed, the legs remain together, and
enclosure to rest the leg latch into so that
The legs of the SpotMax™ have a U-shaped
rograms. Con rm with ENTER button.
display di erent colors. Con rm with the ENTER button. Press the ENTER/PROG button and use the + and – button to display di erent p
Power Out
ATTACH
when open, the legs remain open. The legs
the Di usor Slot, then pressed
also contain a hole to attach a truss clamp.
keep it in place.
RF Antenna
The Di usor Clip should be pressed
Hole for Clamp
Controlling the SpotMax™
Di usor Slot
Set a color or basic e ect through the control pad on the AX10's backside. Press the MENU/COLOR button and use the + and – buttons to
lifted out via the thumb hole.
battery symbol disappears.
Up to 30mins runtime have

Control Panel

remaining; recharge
Over 30mins runtime have
Less than 30mins runtime
been used
Leg Latch
Current E ect
charged the battery icon on the display will show all 3 bars while the power cord is connected. When the battery is fully charged, there will be 3 charging bars on
Battery Icon & Status LED
been used
the battery icon (as below). If the battery is already fully charged and the power cord is plugged in, the display will show a ashing battery icon for approx. 30-60
The Battery Status LED is designed for being used before an event. All xtures should have a green Status LED to ensure that the battery lasts for your upcoming
While the battery is charging the green Status LED will be ashing on and o . Also, the Battery Icon will start the charging sequence. Once the battery is fully
seconds after which ashing will stop and the icon will show 3 charging bars. When the SpotMax™ is turned o and the power cord is connected, the charging
process will begin. This is indicated by the LCD display turning on and the battery icon in the top right corner ashing. When the power cord is disconnected the
Charging
Group Number
event. If it is another color, recharging is recommended.
Empty
30%
DMX Address
Full
70%
IR Sensor
On/O
Icon & LED
Battery
Connect an ART3 (Wireless DMX Transmitter) to your DMX desk to send wireless DMX signals to the AX10. You can set the AX10s DMX
RF
www.astera-led.com/downloads.
W-DMX
IR
Astera's remote control and the AsteraTouch tablet can group several lights together, address individual lights or groups of lights and
although the IR signal should bounce of walls and oor.
Use Astera's ARC1 remote control, point at individual lights and press the desired e ect. Note that the IR sensor is on the AX10 rearside
address on its control pad or send it from a remote control. For additional information refer to the ART3 manual at
www.astera-led.com/downloads.
send complex e ects to all lights in range. For additional information refer to the manual and quick start guide of ARC2 and ARC6 at
See Legend on Reverse
Control Pad
Set Number
Di usor Slots
(without di usor)
13° Spot
(30° di usor)
Wide Angle
(di usor sheet)
Wall Wash
Battery Icon & Status LED
Power In
event. If it is another color, recharging is recommended.
The Battery Status LED is designed for being used before an event. All xtures should have a green Status LED to ensure that the battery lasts for your upcoming
Power Out
While the battery is charging the Status LED will be blue. Also, the Battery Icon will start the charging sequence. Once the battery is fully charged the battery icon
on the display will show all 3 bars while the power cord is connected. When the battery is fully charged, there will be 3 charging bars on the battery icon (as below).
The legs of the SpotMax™ have a U-shaped
will stop and the icon will show 3 charging bars. When the SpotMax™ is turned o and the power cord is connected, the charging process will begin. This is
If the battery is already fully charged and the power cord is plugged in, the display will show a ashing battery icon for approx. 30-60 seconds after which ashing
when closed, the legs remain together, and
enclosure to rest the leg latch into so that
when open, the legs remain open. The legs
indicated by the LCD display turning on and the battery icon in the top right corner ashing. When the power cord is disconnected the battery symbol disappears.
also contain a hole to attach a truss clamp.
Less than 30mins runtime
Up to 30mins runtime have
Full
30%
RF Antenna
remaining; recharge
Over 30mins runtime have
been used
Empty
U-Shaped
been used
Connected to AC
70%
Enclosure
Control Panel
315°
Hole for Clamp
Leg Latch
Battery
Icon & LED
IR Sensor
Current E ect
On/O
Group Number
DMX Address
Set Number
Control Pad
See Legend on Reverse
NOTE:
Each di usor has its
name inscribed on
the edge.
For ideal illumination
the text on the facia
should be facing outwards.
Battery Icon & Status LED
The Battery Status LED is designed for being used before an event. All xtures should have a green Status LED to ensure that the battery lasts for your upcoming
event. If it is another color, recharging is recommended.
While the battery is charging the Status LED will be blue. Also, the Battery Icon will start the charging sequence. Once the battery is fully charged the battery icon
on the display will show all 3 bars (as below). If the battery is already fully charged and the power cord is plugged in, the display will show a battery with moving
bars for approx. 30-60 seconds after which it will stop and the icon will show a full battery. When the SpotMax™ is turned o and the power cord is connected, the
charging process will begin. This is indicated by the LCD display turning on.
Less than 30mins runtime
remaining; recharge
Over 30mins runtime have
been used
Control Panel
Current E ect
Tightener
Group Number
Perfect Spot
Flood
Beam: 13°
Beam: 32°
(without di usor)
(FLOOD di usor)
Up to 30mins runtime have
been used
Connected to AC
Battery
IR Sensor
Icon & LED
Control Pad
See Legend on Reverse
Wallwash
Beam: 17° x 46°
(WALLWASH di usor)
Charging
80%+
15% - 50%
50% - 80%
Less than 15%
On/O
DMX Address
Set Number