Astera SpotMax AX10 Kullanıcı Kılavuzu - Sayfa 2

DJ Ekipmanları Astera SpotMax AX10 için çevrimiçi göz atın veya pdf Kullanıcı Kılavuzu indirin. Astera SpotMax AX10 2 sayfaları.

Sayfayı Yazdır

Astera LED-Technology

Nahestrasse 68-70

55593 Rüdesheim an der Nahe

Kreis Bad Kreuznach

Germany

www.astera-led.com

+49 (0) 671 92028292

Technical Data

The SpotMax™ contains 9 RGBAW Philips LEDs, each containing

15W of LED power, totalling an impressive 135W LED power.

Illuminants:

9 x 15W RGBAW Philips LEDs

Total LED Power:

135W

Light Output:

3,350 lm at 4000K

typical values

3,150 lm at 6500K

3,100 lm at 7500K

Luminous Emittance:

10,350 lx at 2m

typical values

4,700 lx at 3m

1,800 lx at 5m

CRI:

92 at 3000K

(60%-70% intensity)

typical value

Strobe:

0-25Hz

Beam Angle:

13°

(achieved through Khatod lenses)

Battery:

Built-in Samsung battery

Battery Lifetime:

70% capacity after 300 full

charging cycles

Battery Runtime:

5-20 hours

LED Lifetime:

50,000 hours

Working Voltage:

Input 110-240V, 50/60Hz

Power Consumption:

170W

(maximum)

Wireless Module:

868MHz (US: 902-928MHz)

2.4GHz wireless module

Range:

300m / 330yds

(maximum)

DMX Capable:

CRMX Wireless DMX (Lumen Radio)

W-DMX (Wireless Solutions),

or Wireless DMX (with ART3)

Connector:

Neutrik Powercon True1 In/Out

Housing:

Water-resistant cast aluminium

IP Rating:

IP65

Relative Humidity:

0-100%

(non-condensing)

Operating Temperature:

0°-40°C

(32°-104°F)

Weight:

8.15kg

(18lbs)

Dimensions:

L279mm x H296mm x W253mm

L10.9" x H11.6" x W9.9"

Environment:

Indoor / Outdoor

Features:

TruColor™ Calibration, Temperature

compensation, Dynamic

power-boost, Auto-white &

Auto-amber, Dual antennas.

Included Accessories:

Power Cord, 2 x Di usor Sheets

Also Available:

Charging Case

(holds 4)

Troubleshooting

The xture does not start up.

It might be empty. Connect it to the AC power and try again.

The xture starts up and the display is on but the LEDs do not emit light.

The light is probably set to BLACKOUT mode or set to display black color. Use a remote control to change the color. If this does not work, do a factory reset.

The units behave incorrectly and do not display the color or e ect I would like them to.

The xture might still have a setting which was previously programmed. Do a factory reset to completely wipe all settings.

I did a factory reset and still cannot control the light.

Make sure the RADIO PIN of the xture and controller are the same.

The units run out of battery after less than 8 hours.

To get a longer battery runtime, you can set the POWER MODE from HIGH BRIGHTNESS to NORMAL. Or you can program the xture to display colors

that take less power such as Red, Green, and Blue.

The power cable is connected but the xture is not charging.

To protect your battery, the xture will only charge if it is has a temperature of 45 degrees or less. Switch o the xture and the light will cool down.

Menu Structure

INPUT SELECT

WIRELESS DMX The unit uses the RF signal sent by the Wireless SMX Transmitter (ART3)

AUTO SETTING

REMOTE CONTROL The unit uses the RF signal sent by the ARC2 Remote Controller

DMX SETTINGS

STANDALONE The unit ignores all incoming signals and can only be operated through its control panel

GENERAL SETTINGS

AUTO The unit operates in auto mode and chooses any incoming signal

INFO

FACTORY RESET

AUTO SETTINGS

PROGRAM Chooses one of 20 pre-de ned programs that can be customized by colors, intensity, power

scheme, speed, fade, directions etc.

INTENSITY Sets the brightness of the LEDs

SPEED Sets the speed of the programs' e ects

FADE Sets the fade between the program e ect steps

DIRECTION

CHASER Sets di erent color chasers

CHASER SPEED Sets the speed of the color chaser

GROUPS Assigns the light to 1 of 4 groups so they can be easily targeted

OFFSET O set de nes where the LOCAL GROUP starts. Usually this is automatically set by the light,

depending on how many other lights are in a group

CHAIN SIZE See how long the chain should become

PCS IN CHAIN Choose the position the unit should take in the chain

SET SIZE Choose how long the set should become

POS IN SET Choose the position the unit should take in the set

COLOR C1 - User color 1

COLOR C3 - User color 3

DMX SETTINGS

DMX ADDRESS Sets the DMX address

CHANNELS Sets the amount of channels that are used to control one unit. One RGB channel

means that all LEDs have the same color

DMX TAB

STROBE

DMX FAIL

GENERAL SETTINGS

LED POWER

BELONGS TO SET# Assigns the light to 1 of 255 sets so they can be easily targeted

WHITE CORRECTION Turns the white correction on/o

WHITE CALIB RED Adds or reduces the amount of red when displaying white light

WHITE CALIB GREE Adds or reduces the amount of green when displaying white light

WHITE CALIB BLUE Adds or reduces the amount of blue when displaying white light

RADIO PIN Assigns a unique frequency to ensure uninterrupted use when other controllers are present

AC FAILURE

CONTRAST Sets the contrast of the display beween 1 and 48

INFO

Serial number

Power-on hours

Temperature

Battery state

Calibration

FACTORY RESET

ARE YOU SURE?

YES

COLOR C2 - User color 2

COLOR C4 - User color 4

Firmware version

RF Link

Radio pin

Battery health

Messages

Safety

Before you operate this unit, read the manual carefully. Always make sure to include

the manual if you pass/rent/sell the unit to another user. Keep in mind that this

manual cannot address all possible dangers and environments. Please use your own

caution when operating.

Do not operate the unit in areas of temperature conditions or under direct sunlight.

It will cause abnormal function or damage the product.

Only quali ed personnel may repair this product. Do not open the product housing.

A rechargeable battery is built into this unit. Please avoid bumping or plunging, it will

cause FIRE or EXPLOSION. Never store the battery when fully drained. Always recharge

immediately when empty.

Make sure to fully charge all units before storing them. Partially charged batteries will

lose capacity. Do not store the unit longer than 3 months without re-charging.

LEGEND

BACK TO

SCROLL

CHOOSE/

PREVIOUS MENU

DOWN

CONFIRM

DIRECTION Adjusts direction and looping of programs' e ects

FFW+LOOP Programs run in normal (forward) direction. When a program nishes, it starts over

REV+LOOP Programs run in reversed direction. When a program nishes, it starts over

FFW Program runs in normal (forward) direction.

FWD Programs run in normal (forward) direction. When a program is nished, execution is stopped

REV Programs run in reversed direction. When a program nishes, it stops.

DMX TAB Several di erent DMX tables can be chosen

RGB S RGB S.. For each pixel, there are three channels RGB and one channel stroboscope

RGB RGB S S .. All RGB channels are followed by all stroboscope channels

EFFECT MODE MIX The four user colors are controlled

EFFECT MODE RGB The four user colors are controlled by three DMX channels

RGBAW S For each pixel 5 channels can be set individually, followed by 1 channel stroboscope

RGB CCT DIM IND Seven channels control each pixel, apart from RGB values, the color temperature, index

color, a seamless brightness control, and strobe can be set

STROBE Sets a series of strobe e ects

SINGLE One DMX channel is supplied for the control of the stroboscope function and all pixels' strobe will be

identical. When using this setting, DMX TAB should not be set to RGB S RGB S ..

MULTIPLE For each pixel, the stroboscope can be controlled individually

OFF Stroboscope is turned o globally. One DMX channel is supplied for the control of the stroboscope

function and all pixels' strobe will be identical. When using this setting, DMX TAB should not be selected

DMX FAIL detects AC power loss (if plugged in)

HOLD The output remains unchanged, the last DMX frame is displayed

EMERGENCY LIGHT LEDs turn white until AC power is restored

BLACKOUT LEDs turn dark in case of AC power loss

AUTO PROGRAM Plays the program set in AUTO SETTINGS > PROGRAMS

LED POWER 3 di erent power schemes can be set to optimize the playback

MAXIMISE RUNTIME The lights are less bright but battery will last up to 24hrs

NORMAL The lights are normal brightness and battery will last at least 8hrs

HIGH BRIGHTNESS The lights are set to a brightness that is stronger than usual but will drain the battery

quickly

AC FAILURE Sets the behaviour when no AC signal is detected

EMERGENCY LIGHT If no AC signal is detected, the light turns white

NO ACTION The playback continues as before

BLACKOUT If no AC signal is detected, all lights will turn o

The exterior surfaces of the SpotMax™ can become hot,

up to 70° C (158° F), during normal operation. Ensure that

accidental physical contact with the devices is impossible.

Allow all AX10 devices to cool before servicing. Use only

Astera approved accessories to di use or modify the light

beam.

Do not directly look at the light beam for long periods. It

can cause harm to your eyes. Do not look into the beam at

a distance of less than 0.5 meters (20 inches) from the front

surface of the product, and do not look at LEDs with a

magnifying glass or any other optical instrument that may

concentrate the light output.

This product is for professional use only. It is not for

household use.