American Time EverAlert Kurulum Kılavuzu - Sayfa 2

Modem American Time EverAlert için çevrimiçi göz atın veya pdf Kurulum Kılavuzu indirin. American Time EverAlert 2 sayfaları.

Sayfayı Yazdır

INTEGRATOR QUICK START INSTALLATION GUIDE

Mounting

1. Wall Mount

a. Position EverAlert Integrator in the desired location.

b. Use at least one screw on each flange of EverAlert Integrator to

attach to wall.

2. Desktop, Shelf or Table Top

a. Place EverAlert Integrator upside down on a smooth, flat

surface.

b. Peel off the rubber feet from the adhesive strip and place them

down onto each corner of the EverAlert Integrator.

c. Turn over the EverAlert Integrator so that it is resting on the

rubber feet.

Wiring

The EverAlert Integrator (INPUT 1 or INPUT 2) can be connected to

any normally open contact closure type switch. The Integrator can

also be connected using the Output function as shown below to

activate a secondary device (such a strobe or siren) when an alarm

becomes active. See section 11 for details on the Output function.

All EverAlert Displays configured on the same Site as the EverAlert

Integrator will have their full screen alarms triggered when the Input

contact closure switch is closed. They will remain active until the

switch is opened again. See wiring diagram below for inactive state.

+ from device

power source

+ to device

function

Switch Example

Alarm Panel Example

NC NO

AUX RELAY

Network In

9V Power Supply

Installation

1. Connect the supplied external power supply to the barrel jack

power connector and plug into AC wall receptacle.

2. Connect Ethernet cable to EverAlert Integrator and to a network

switch or router.

Alarm Definitions

EverAlert sites come with a number of preconfigured alarms. To add

a new alarm, follow the steps below.

a. Login to incloud.american-time.com.

b. Click on the Site where the EverAlert Integrator will be installed.

c. Select "Alarm Definitions" from the Admin drop down menu.

d. Click on "Alarms," then click "Add New" at the top of the page.

e. TITLE: Enter the Alarm Title (i.e. Fire, Tornado or Lockdown).

f. INSTRUCTIONS: Enter the information that will display on the

screen when the Alarm is triggered. This is most commonly

the instructions that provide direction to the recipients of the

message.

g. PRIORITY: Select the Alarm priority. The priority sets the

override sequence with 1 being the highest to 10 being the

lowest. The higher priority Alarm will override the lower priority

Alarm if both occur at the same time.

h. AUDIO: Select an audio file for the Alarm.

i. PANEL COLOR: Select the panel color for the display

NO = Normally Open

C = Common

background when the Alarm is triggered.

NC = Normally Closed

j. MOBILE BUTTON COLOR: This is the color of the button that

issues the Alarm from the mobile device.

k. MOBILE ENABLED: Enables or disables the ability to send the

Alarm from a mobile device.

l. ENABLED: Enables or disables the Alarm. If disabled, the Alarm

will not display as an option for the integrator.

m. Click on the green Save button to save the Alarm.

n. Repeat steps d – m for additional Alarms Definitions.

+9Vdc

Configure the EverAlert Integrator on

inCloud

a. Click on "Alarm Integrators" from the Admin drop down menu.

b. Click "Add New" at the top of the page.

c. MAC: Enter the serial number from the bottom of the Integrator.

Carefully verify the serial number entered into the field matches

the number on the device as this field cannot be edited once

saved.

d. NAME: Enter the desired name of the integrator.

e. INPUT 1 ALARM: Select the desired Alarm from the drop down

list.

f. INPUT 2 ALARM: Select the desired Alarm from the drop down

list.

g. DESCRIPTION/NOTES: A brief description about the device

such as the location of the Integrator can be entered here.

h. Click the green Save button.

i. If the displays have been already installed and provisioned, the

screen will populate a list of all the displays for that site and all

the displays will automatically be assigned to the Integrator.

For each additional Integrator added, the displays will be

automatically assigned to the Integrator. If adding more than one

Integrator to the site, the displays will need to be assigned as

desired after the last Integrator has been added. Reference the

Installation Manual for assigning displays.

j. Repeat steps a – h for additional Integrator devices.

If using the Output function, the desired parameters for the Output

to be activated can be set on the Edit Integrator page, which can be

reached by clicking on the Integrator name while in the Device List.

The Output can be set to be triggered by All Alarms (meaning both

Inputs and all Weather Alerts), by following either one or both of the

Inputs (meaning the Output will be triggered any time the specified

Input is active), or by specific Weather Alerts. Note that only Alert-

level Weather Alarms will be available.

TITLE (See 7 e.)

PANEL COLOR (See 7 i.)

INSTRUCTIONS (See 7 F.)

EverAlert

emergency communication platform

Sample