Astivita WMTL7KGWH Kullanıcı El Kitabı - Sayfa 4

Yıkayıcı Astivita WMTL7KGWH için çevrimiçi göz atın veya pdf Kullanıcı El Kitabı indirin. Astivita WMTL7KGWH 11 sayfaları. Full automatic electric washing machine

Sayfayı Yazdır

Installation of the washer

Remove package

Remove package and take out the bottom board of

the cabinet on the foam cover.

Open the lid of washer's door and take out accessories.

A trial operation or washing on the foamed cushion is

strictly forbidden.

Installation of drain hose

Placement of water drain hose

Under3m

If the water drain hose shall

The placed height of water

be extended, its length shall

drain hose shall not exceed

not exceed 3 meters,

15cm.

otherwise it will affect the

water discharging time.

FOR LOWER DRAIN SYSTEM ONLY

Placement of upper water drain hose

The height of drain hose ("a")should between 86-100 cm.

Diameter of "b"shuld not less than 3 cm, and flow capacity

not less than 40 L/Min.

Before washing machine starts, user should hang up

the drain pipe 86-100cm height from the floor.

FOR UPPER DRAIN SYSTEM ONLY

Installation of water inlet pipe

Put the water inlet pipe(which has

metallic filtering bag) screw on to the tap.

Tightly screw another end of water

inlet hose on water inlet valve .

(with rubber seal ring inside).

Note: When tightening the

clamping nut, evenly apply the

force and do not twist the water

inlet valve to avoid breaking of

water inlet valve joint.

Base foamed cushion

Completely sleeve the drain

hose over the sewer.

Fix and tighten it with a hoop.

( As shown in the figure )

Under 15cm

Do not bend the water

drain hose and place

it under the washer.

86~100 cm

Clamping nut

Water inlet hose

Only for model with double

screw thread water inlet pipe

5 5

Installation of the washer

Installation of water inlet pipe

Small ball

Push down the slide jacket

to expose the small balls and

enable separation of connector

socket from speedy connector.

not flat) and push it upward with force making the rubber

washer firmly press the plane center of water tap mouth.

5mm

Junk ring

Then tighten the screw sequentially. After that, tightly

screw on part B.

The connection socket

Connect: Push down the slide jacket

consists of A and B two

of speedy connector (4 small balls

parts. Before installation,

must be exposed ),insert it into the

A and B two parts must

connection socket and then push

be unscrewed about

upward Release the connection

5mm, or directly

of water tap with speedy connector

disconnected. If the

completely. If it is required to feed

bore of water tap is

water, simply open the water tap.

larger, remove the

Separate: Close the water tap, push

Connect

plastic junk ring of

down the slide jacket of speedy

part A.

connector and pull out the speedy connector.

Tightly screw another end of water inlet

hose on water inlet valve . (with rubber

seal ring inside).

Note: When tightening the clamping nut,

evenly apply the force and do not twist

the water inlet valve to avoid breaking of

water inlet valve joint.

Only for model with single screw thread water inlet pipe

If the supply cord is damaged, it must be replaced by the

manufacturer, its service agent or similarly qualified persons

in order to avoid a hazard.

the appliance are to be used and that old hose-sets should

not be reused.

The openings must not be obstructed by a

carpet.This appliance is for indoor use only.

Unscrew four screws of part A

and sleeve part A horizontally

over the mouth at the end of

water tap (the mouth at the end

of water tap must be flat and

smooth. Flatten it by filing if it is

Separate

Water inlet hose

Clamping nut

The new hose-sets supplied with

6 6 6