Donmar SH-R-01 Kurulum Talimatları Kılavuzu - Sayfa 2

Isıtıcı Donmar SH-R-01 için çevrimiçi göz atın veya pdf Kurulum Talimatları Kılavuzu indirin. Donmar SH-R-01 9 sayfaları. Seat heaters universal: dual temperature carbon fiber: twin comfort pads

Sayfayı Yazdır
Index
1.
General safety advice . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
2.
Component list ... . . . . . . . . . . . . . . . . . . . . . . . . . . . . ... . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
3.
Pre-Installation Summary & OCS............................................................................................................................. 4
3.
Installation instructions including OCS / OPDS information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-6
4.
Wiring diagram......... . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
5.
Operating instructions.......... . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8
A
a = min. 250 mm
a = min. 9 1/32"
B
03 Jan 2009
.
General safety advice
1.
It is impossible to install a Seat Heater kits whenever;
-
• The seat covers are adhered to the seat's foam padding, or
• The distance between listing channels are spaced less than 10" apart.
-The battery terminals should be disconnected prior to working on
the vehicle's electrical circuits. Security codes (radio, navigation
system, etc.) should be noted.
-Do not modify the seat cover or seams of seats with side air-bags.
- Refer to owner's manual for seats with integrated seat belts or
a
occupant detection sensors for air bags.
- The heating elements are only allowed to be installed by a qualified
professional who is knowledgeable about electronic systems and
upholstery.
- Use original kit components only.
a
- The heating elements must be secured and mounted free of folds and
creases. Any exposure to sharp objects will compromise the integrity
of the heating element. For durability and system reliability, the
heating element must be positioned correctly.
- The heating element is only allowed to be operated at +12 V ±3 V. It
should be connected to the onboard power supply via ignition voltage
and the protective fuse should ideally be put in an empty bay in the
fuse box. The maximum fuse rating is 12 amps.
- The heating elements are only allowed to be modified as described in
these installation instructions (B).
- The wire harness must not be modified and must be routed so the seat
can move freely. Contact with sharp edges, bending or pulling of wire
must be avoided to prevent the wire harness from being damaged. The
onboard main supply and wire harness cross-section must be adapted
to the extra current loads if necessary. Refer to the vehicle's wiring
diagram for additional information.
- The foam padding must be clean and free of any dirt. Sufficient
pressure should be applied to the adhesive sections of the pads to
ensure a solid bond between foam and pad. Do not detach and
reinstall an element after it has been installed for the first time.
- The heating elements must not contact the seat's electrical conductive
components such as hog rings or the seat's frame in any way or you
risk the Danger of Short-Circuiting!
- The heating performance at the cover's surface varies according to the
type of seat or cover. Every millimeter of the cover's foam thickness
prolongs the heating time by up to 15 seconds.
- The seat heater functions must be explained to the customer and the
Operating Instructions Section of this installation guide must be
provided. The customer must be informed about all safety aspects.
The operating instructions must include the fuse location and its
position.
- The points in the operating instructions must be followed for the
installation.
Warning: Seat heaters must not be installed in vehicles that will be used by paraplegic or other
occupants who cannot sense heat. Customers must notify the original installer if the vehicle is sold to
a third party.
2