DoorHan CV01 Kurulum ve Kullanım Kılavuzu - Sayfa 3
Kontrol Ünitesi DoorHan CV01 için çevrimiçi göz atın veya pdf Kurulum ve Kullanım Kılavuzu indirin. DoorHan CV01 4 sayfaları.
Ayrıca DoorHan CV01 için: Kullanıcı El Kitabı (12 sayfalar), Manuel (8 sayfalar)
Sayfayı Yazdır
1. Intended Use of the Product
DoorHan CV01 control unit is intended to be used in either wired
applications or in wireless applications to control:
electric locks,
electric operators of garage doors,
electric operators of sun blinds, rolling shutters,
indoor lighting; as well as to enable use of DoorHan consoles
with operators of other manufacturers and to automate
various devices.
2. Specifications
Supply voltage
Allowable switching current — max.
Switching voltage — max.
Protector operation current rating
Number of controlled electric operators
Dimensions
Weight — max.
Environment temperature as per GOST 15150
Electrical safety class as per GOST 27570
STEPPED CONTROL:
from remote control unit: opening — stop — closing —
stop
from switch: opening — stop — closing — stop
–12
+
–12 +
11
12
T
TR1
F1
P2
P3
VR1
1
2
3
4
5
6
7
N
L1
N
220
L1
220 , 50
N
Fig. 1 Example of lighting and external
radio control connection diagram
(to DoorHan CV01)
220 V, 50 Hz
98 × 98 × 56 mm
COM
NO
13
14
P
8
9
10
Fig. 3 Rolling shutter motor and external
CV01 CONTROL UNIT INSTALLATION
AND OPERATION GUIDE
3. Installation
1. Remove protective packaging from the control unit. Remove
the cover of the control unit housing using a screwdriver.
2. Unscrew carefully two fixing bolts of the control unit panel
and take it out of the housing.
3. Connect wiring according to the diagram (Fig. 1 and 2).
4. Fix the control unit panel in the housing and place the cover
back.
When installing the device, protect it from dust and moisture.
When connecting equipment wires, if possible, use mounting
holes from the side of the terminal block (not on the top). Before
connecting, pierce the rubber plugs using an awl or a thin screw
driver (Fig. 1) so that the diaphragm fits tightly the inserted wires.
7 А
Note:
220±10 V
the minimum distance from the earth — 50 sm;
4 А
the distance between neighboring control units shall be
1
at least 20 sm;
it is recommended to bring the receiver antenna out of the
400 g
housing for better radio signal receiving.
from –40
to +70°С
4. Programming
II
CONTROL UNIT OPERATION MODE
1. STANDBY
After the control unit power is on, it will be in standby mode
until either a command is given from the switch or from the
remote control unit or change to the programming mode is done.
–12
+
COM
NO
E
–12 +
11
12
13
14
T
P
TR1
F1
P2
P3
VR1
1
2
3
4
5
6
7
8
9
10
N
L1
N
220
L1
220 , 50
N
radio control connection diagram
(to DoorHan CV01)
–12
+
COM
–12 +
11
12
13
T
TR1
F1
P2
P3
VR1
1
2
3
4
5
6
7
N
L1
220
220×12, 15 W
~220 , 50
AC 12 V
Fig. 4 Electric lock control
connection diagram
NO
14
P
8
9
10