Canon PIXMA MP610 Series Servis Kılavuzu - Sayfa 8
Hepsi Bir Arada Yazıcı Canon PIXMA MP610 Series için çevrimiçi göz atın veya pdf Servis Kılavuzu indirin. Canon PIXMA MP610 Series 45 sayfaları. All-in-one photo inkjet printer
Ayrıca Canon PIXMA MP610 Series için: Buradan başlayın (2 sayfalar), Tamamlayıcı Kılavuz (6 sayfalar), Broşür ve Teknik Özellikler (2 sayfalar), Hızlı Başlangıç Kılavuzu (40 sayfalar), Hızlı Başlangıç Kılavuzu (2 sayfalar)
Sayfayı Yazdır
- 1. Table of Contents
- 1. 1 Maintenance
- 1. Adjustment, Periodic Maintenance, Periodic Replacement Parts, and Replacement Consumables by Service Engineer
- 1. Customer Maintenance
- 1. Special Tools
- 1. Serial Number Location
- 2. 2 List of Error Display / Indication
- 2. Operator Call Errors
- 2. Service Call Errors
- 2. Other Error Messages
- 2. Warnings
- 2. Troubleshooting by Symptom
- 3. 3 Repair
- 3. Notes on Service Part Replacement
- 3. Adjustment / Settings
- 3. Verification Items
2-2. Service Call Errors (by Cyclic Blinking of Alarm and Power LEDs)
Service call errors are indicated by the number of cycles the Alarm and Power LEDs blink, and the corresponding error code with
the message,
"Printer error has occurred. Turn off power then back on again. If problem persists, see the manual." is displayed on the LCD.
Cycles of
blinking of
Alarm and
Power LEDs
2 times
Carriage error
3 times
Line feed error
4 times
Purge cam sensor error
5 times
ASF (cam) sensor error
6 times
Internal temperature error [5400] The internal temperature is not normal.
7 times
Ink absorber full
8 times
Print head temperature
rise error
9 times
EEPROM error
10 times
VH monitor error
11 times
Carriage lift mechanism
error
12 times
AP position error
13 times
Paper feed position error [6B00] An error occurred in the paper feed
14 times
Paper feed cam sensor
error
15 times
USB Host VBUS
overcurrent
16 times
Pump roller sensor error
17 times
Paper eject encoder error [6010] An error occurred in the paper eject
Error
Error
code
[5100] An error occurred in the carriage encoder
signal.
[6000] An error occurred in the LF encoder
signal.
[5C00] An error occurred in the purge unit.
[5700] This error takes place when feeding
paper from the rear tray after an error
occurred in the ASF cam sensor.
[5B00,
The ink absorber is supposed to be full.
5B01]
Message on the LCD:
Error codes:
[5200] The print head temperature exceeded the
specified value.
[6800] A problem occurred in writing to the
EEPROM.
[B200] The internal temperature exceeded the
specified value.
[5110] The carriage did not move up or down
properly.
[6A00] An error occurred in the AP motor
during purging operation.
motor during line feeding.
[6B10] An error occurred in the paper feed cam
sensor during paper feeding from the
cassette.
[9000] The USB Host VBUS is overloaded.
[5C20] The pump roller position cannot be
detected.
encoder signal.
Conditions
Ink absorber full. Service required.
5B00: Main ink absorber is full
(overseas).
5B01: Main ink absorber is full
(Japan).
6 / 43
Solution
(Replacement of listed
parts, which are likely to be
faulty)
- Carriage unit
- Timing slit film
- Logic board
- Carriage motor
- Timing sensor unit
- Timing slit disk film
- Feed roller
- Logic board
- Paper feed motor
- Purge unit
- Logic board
- Sheet feed unit
- ASF_PE sensor board
- Logic board
- Logic board
- Ink absorber kit
- Print head
- Logic board
- Logic board
- Print head
- Carriage unit
- Logic board
- Sheet feed unit
- PR lift shaft ass'y
- Carriage lift sensor unit
- Logic board
- Sheet feed unit
- Purge unit
- Logic board
- Sheet feed unit
- Logic board
- Sheet feed unit
- Logic board
- Logic board
- Purge unit
- Logic board
- Platen unit
- Timing sensor unit