DoorKing 8054-083 Manuel - Sayfa 2

Alıcı DoorKing 8054-083 için çevrimiçi göz atın veya pdf Manuel indirin. DoorKing 8054-083 4 sayfaları. High security encrypted “rotating code” rf receiver

Sayfayı Yazdır

Programming

Programming BEEPS:

The receiver is equipped with a "beeper" to help guide you through the programming steps. When required data has

been entered correctly and the

there has been NO data input for 20 seconds. Four (4) long beeps in a row indicates that an error has occured (Examples: Data was entered

incorrectly, not enough memory to store all transmitters or receiver is in real time printing mode but printer is not connected or not turned on).

o d

r C

s t e

t t o

B u

M a

Add a Transmitter:

Unique codes located on back of transmitter (Five-digit Transmitter Code - Tr) and (Four-digit Facility Code - Fc).

1. Press

and the four-digit Master Code.

2. Enter the two-digit transmitter button number that the receiver is to respond to, then press

3. Enter the four-digit facility code, then press

4. Enter the LOWEST five-digit transmitter code, then press

5. Enter the HIGHEST five-digit transmitter code, then press

Note: Valid transmitter codes are 00000 - 65407.

If adding a single transmitter, the lowest and highset five-digit number will be the same.

6. Enter the single-digit Time Zone number, then press

Note: Valid Time Zones are 0 - 9.

There are 10 available time zones. Time zones 2 - 9 are programmable (See "Programming Time Zones" programming on next page).

Entering

will never allow access to the transmitter(s) being programmed.

Entering

will always allow access to the transmitter(s) being programmed.

When programming a block of transmitter numbers, the receiver will

Wait for this beeping to stop before proceeding with any other programming.This may take up to five

minitues depending on the memory size and the number of transmitters being programmed.

7. Repeat steps 2 - 7 to enter an additional transmitter or block of transmitters or press

to end the programming. A

Delete a Transmitter One at a Time:

(Four-digit Facility Code - Fc).

1. Press

and the four-digit Master Code.

2. Enter the two-digit transmitter button number to be deleted, then press

3. Enter the four-digit facility code to be deleted, then press

4. Enter the five-digit transmitter code to be deleted, then press

3. Repeat steps 2 - 4 to delete additional transmitters if desired or press

to end the programming. A

Delete ALL Transmitters at Once:

1. Press

and the four-digit Master Code.

2. Enter 9999, then press

3. After approximately 1 1/2 minutes of

heard when finished.

"BEEP"

key is pressed, a

Program the Master Code:

the four-digit number required to gain access to the

receiver memory for all programming. You MUST

program a MASTER CODE first.

1. Press Master Code Button

L E

2. Choose and enter four-digits on the keypad

R F

Important Note:

code . There is NO way of retrieving the master code after it has been programmed in. If you

forget it, you will have to program in a new master code but all other previously programmed

information will remain intact.

"BEEP"

"BEEEEEEEEEP"

will be heard when finished.

Unique codes located on back of transmitter (Five-digit Transmitter Code - Tr) and

"BEEP"

"BEEEEEEEEEP"

will be heard when finished.

WARNING: Deleted transmitters CANNOT be retrieved.

"BEEP"

"BEEPS"

every three seconds, one long

"BEEEEEEEEEP"

will be heard. A

The master code is

Keep this instruction sheet for future reference after writing down the master

Note: Valid facility codes are 0000 - 4095.

"BEEP"

every three seconds.

"BEEP"

at the same time or simply wait 20 seconds

"BEEEEEEEEEP"

indicates programming has ended successfully OR

Write Down Your Master Code

1st Digit 2nd Digit 3rd Digit 4th Digit

any four numbers

Button 1 -

"BEEP"

Button 2 -

Button 3 -

Buttons 1&2 together -

Buttons 2&3 together -

Buttons 1&3 together -

at the same time or simply wait 20 seconds

will be

Inglewood, California 90301

"BEEP"

then press

120 S. Glasgow Avenue

U.S.A.