Canon PIXMA MX850 Kurulum Talimatları

Hepsi Bir Arada Yazıcı Canon PIXMA MX850 için çevrimiçi göz atın veya pdf Kurulum Talimatları indirin. Canon PIXMA MX850 2 sayfaları. Multifunction brochure
Ayrıca Canon PIXMA MX850 için: Ağ Kurulum Kılavuzu (43 sayfalar), Tamamlayıcı Kılavuz (6 sayfalar), Broşür (2 sayfalar)

Sayfayı Yazdır

Unpack the Machine

•

Please confirm the included items against the illustration printed on the lid of the packing box.

•

A USB cable is necessary to connect the machine with your computer.

Prepare the Machine

Lift the Scanning Unit (Printer Cover)

Plug the power cord in the back of the

until it locks into place, open the Paper

machine and connect the other end to

Output Tray, then take out the Print

the wall outlet.

Head, ink tanks and power cord from

Document Cover

inside the machine.

Caution

•

Before turning on the machine, remove all of the

shipping tapes and protective material.

•

For your safety, always firmly grip the areas il-

Important

lustrated when lifting the Scanning Unit (Printer

•

Make sure that the Document Cover is closed.

Cover).

•

Do NOT connect the USB cable at this stage.

Press the ON/OFF button to turn on the

machine.

The machine will initialize. Wait until the COPY

button stops flashing and remains lit green.

Important

If the Document Cover is opened, you cannot open

the Scanning Unit (Printer Cover). Be sure to open

Press the { or } button on the

the Scanning Unit (Printer Cover) with the Docu-

Operation Panel to select the language

ment Cover closed.

for the LCD, then press the OK button.

Remove the protective material in the

ADF (Auto Document Feeder).

Protective Material

Important

If an unintended language is displayed on the

Note

LCD, press the Back button on the Operation

The tape or the protective material position is subject

Panel to return to the Language selection screen.

to change.

Once the message "Install the print head and

Connect the telephone line and any

set the ink tank." appears, go to g.

necessary external device.

You can connect an external device (telephone

Lift the Scanning Unit (Printer Cover)

or answering machine) if necessary.

until it locks into place. The Paper Output

Tray will open automatically and the Print

Remove the Telephone connector cap to

Head Holder moves to the center. Then

connect the external device.

open the Output Tray Extension.

If the Paper Output Tray does not open

automatically, press the Open button to open it.

Telephone connector cap

Connect the telephone

line cable to the wall jack.

Connect external devices as follows:

External Device Jack

Telephone Line Jack

Telephone or answering machine

Telephone or

Telephone

line

answering machine

Machine

Open the Inner Cover. Write down

Built-in computer modem and telephone

the serial number located inside the

LINE TEL

Telephone

machine. You will need this to register

Computer

your product.

Telephone

Machine

line

Important

Be sure to use the bundled telephone line cable.

Start Here

Easy Setup Instructions

Install the Print Head

Remove the Print Head from its

package.

Caution

There may be some transparent or light blue ink

on the inside of the bag the print head comes in,

or the inside of the protective cap - this has no

effect on print quality. Be careful not to get ink on

yourself when handling these items.

Remove the orange protective cap from

the Print Head and discard it.

Important

Do not touch the print head nozzles or the electri-

cal contacts.

Firmly raise the Print Head Lock Lever

(1) Press the { or }

until it stops. The Print Head Lock

button to select the

Lever may feel heavy.

language.

(2) Press the OK button.

Important

•

Make sure that the machine is turned on and the

COPY button lights green.

•

Make sure that the Print Head Holder has moved

to the center.

Insert the Print Head.

Do not touch!

Push the Print Head to hold it in place,

and lower the Print Head Lock Lever.

Important

If the Scanning Unit (Printer Cover) is left open

for more than 10 minutes, the Print Head Holder

moves to the right. Close and reopen the Scanning

Unit (Printer Cover) to return the Holder to the

center.

Inner Cover

Serial Number Location

Important

When cleaning the exterior of the machine, use a soft cloth to wipe it gently. For details, refer to "Cleaning Your Machine" in the Quick Start Guide.

Install the Ink Tanks

Note

For the ink tanks compatible with this machine, refer to

the back cover of the Quick Start Guide.

Do not touch!

Pull the orange tape in the direction of

the arrow to peel off the protective film

and remove the film completely.

If the air hole is blocked with the remaining film, ink

may leak out or may not eject properly.

Twist off and discard the orange

protective cap located on the bottom of

the ink tank.

Protective Cap

Do not press!

Electrical Contacts

Important

•

Do not touch the electrical contacts.

•

Do not touch the ink port.

Print Head Nozzles

Insert the ink tank into the right-hand

Protective Cap

slot and press the

mark on the ink

tank until it clicks into place.

Make sure the ink lamp lights red.

Refer to the color

guide on the Print

Head Lock Lever.

Close the Inner Cover and the

Scanning Unit (Printer Cover).

Caution

For your safety, always firmly grip the areas il-

lustrated when closing the Scanning Unit (Printer

Cover).

Important

The machine starts the preparatory operation.

It takes about two minutes. Do not start another

operation until the machine has stopped making

operating noises.

Note

If the Alarm lamp lights and an error message is

displayed on the LCD, refer to "An Error Message Is

Displayed on the LCD" in the Quick Start Guide.

Align the Print Head

Open the Rear Tray Cover, pull out the

Paper Support, then pinch the Paper

Guide and slide it to the left end.

Paper Support

Extension

Paper Guide

Rear Tray Cover

Load two sheets of supplied paper

(MP-101) into the Rear Tray with the

Ink Port

printing side (whiter side) facing up,

align the paper with the Cover Guide

on the right side, then slide the Paper

Guide against the paper stack.

Paper Guide

Print Side

Cover Guide

Make sure that Yes is selected in the

message requesting head alignment,

then press the OK button.

Note

Print Head alignment takes about 13 minutes to

complete. Do not start another operation until the

machine has stopped making operating noises.

The pattern is printed. And Print Head is aligned

automatically.

Note

•

The pattern is printed in black and blue.

•

When Automatic Print Head Alignment cannot be

executed correctly, the message "Auto head align

has failed." is displayed on the LCD. Refer to "An

Error Message Is Displayed on the LCD" in the Quick

Start Guide.

Hardware setup and Print Head

alignment are complete.

Office All-In-One

For fax users

To use a fax, you need to set the telephone

line type setting properly on the machine.

If you are unsure of your telephone line type,

contact your telephone company.

Select the receive mode according to your

needs.

•

When you receive mainly faxes and

sometimes voice calls:

→ FAX priority mode

•

When you have a dedicated telephone line

for fax use only:

→ FAX only mode

•

When you receive mainly voice calls and

sometimes faxes:

→ TEL priority mode

•

When you subscribe to a ring pattern

detection service provided by your

telephone company, and you want to

receive a fax only if the machine detects

the pattern for fax:

→ DRPD

For details on how to confirm and change

the settings, refer to the Quick Start Guide.

For USB connection, proceed to the

Step 5 on the reverse side.

For wired LAN connection, refer to the

Network Setup Guide.