AmerTac TMDW40 Kullanım Kılavuzu & Garanti

Zamanlayıcı AmerTac TMDW40 için çevrimiçi göz atın veya pdf Kullanım Kılavuzu & Garanti indirin. AmerTac TMDW40 3 sayfaları. Digital wall switch timer

Sayfayı Yazdır

TMDW40

Instruction Manual & Warranty

Indoor

Digital Wall Switch Timer

- Wire in accordance with National and Local Electrical Codes.

- This device requires installation by a licensed electrician or qualified

professional. Use of high voltage detector or meter is recommended.

- Turn power OFF at circuit breaker or fuse box.

- Remove and disconnect the existing switch.

- Connect TMDW40 wire leads to LOAD according to diagram.

- Turn power back ON at circuit breaker or fuse box.

Getting Started

- Lift up bottom of door using a small flathead screwdriver.

- Position the slide switch to TIMER.

- Press the RESET button using a paper clip.

- The display should flash 12:00AM Monday,

see Figure 1.

- If screen is blank, be sure slide switch is on

time, check LOAD connected to the TMDW40

and check 208-277VAC power source.

Setting Current Time

- Press and hold CLK (Clock) button during entire process.

- Press HOUR button to advance the hours.

- Press MIN button to advance the minutes.

- Press DAY button to advance the day.

(If any key is pressed for a prolonged period, display will advance rapidly)

Release the CLK button once time and day have been entered. Timer is now

ready to be programmed. The colon after the hours will continue to flash,

indicating time is advancing.

Programming ON/OFF Events

1. Press PROG button once, display will look as

shown in Figure 2, indicating ON programming

of timer setting 1.

2. Using HOUR and MIN buttons, enter desired

ON time. It is necessary to press MIN at least

once to have "00" for minutes. By default, all

days are indicated.

3. When complete, press the PROG button again,

display will look as shown in Figure 3, indicating

OFF programming of timer setting 1.

4. Using HOUR and MIN buttons, enter desired OFF time. It is necessary to

press MIN at least once to have "00" for minutes. By default, all days are

indicated. If done, press CLK button to return to current time and day.

5. To set additional ON/OFF cycles (maximum of 7 events) press PROG

button and follow procedures in steps 1 to 4 for each new ON/OFF event.

Block Programming

When programming ON/OFF events, all days are indicated by default, To

change day selection, press DAY button and display will change as follows:

- Individual day (MO, TU, etc)

- MO-FR, SA-SU, MO-SA, MO-SU

- MO-WE-FR, TU-TH-SA

- MO-WE, TH-SA

Follow steps above to complete programming.

Random Function

Turns On/Off within 2-30 minutes of your programmed settings. To activate

Random Function, press DAY and HOUR button until TIMER flashes on

display. Press again to cancel.

Daylight Savings Time Function

Adds 1 hour to current time to adjust for Daylight Savings Time.

Press MIN and HOUR buttons simultaneously until DST is on display.

Press MIN and HOUR buttons again to go back 1 hour.

208-277VAC Hot

Neutral

* Note: Ensure neutral (white) wire is present in junction box. If this wire is not present,

Figure 1

additional wiring will be necessary before installation can be completed.

Consult a qualified electrician.

Off/Timer Switch

To turn off all programs, move switch to OFF position. Timer will not run any

programs when switch is in OFF position. Programs will be saved by battery

for up to 30 days.

Reviewing Programs

To review programs that have been entered, press and release

PROG button to scroll through programs. Any program can be edited by

pressing the HOUR, MIN, and DAY buttons. Press PROG button to accept

changes. When done, press CLK button to return to current time and day.

MO TU WE TH FR SA SU

Deleting Programs

Press PROG button until desired program is displayed.

Press the ON/OFF button until - - : - - is displayed.

When done, press CLOCK button to return to current time and day.

Figure 2

Manual Override

Pressing ON/OFF button will alternate the unit ON or OFF.

MO TU WE TH FR SA SU

OFF

Figure 3

RATINGS

208-277V~, 60Hz

10A General Purpose

6A Tungsten

2HP Motor

4A Ballast

Limited One Year Warranty

AmerTac™ warrants this product to be free from defects in material and

workmanship for a period of one year from the date of purchase. AmerTac's

obligations are limited to repairing or replacing any defective unit and are

effective only if such units are returned within one year of the purchase date

to AmerTac, 250 Boulder Drive, Breinigsville, PA 18031. Warranty void if

damage is due to misuse or improper installation. In no circumstance will

AmerTac be liable for consequential or incidental damages relating in any

way to this product.

Questions? 201.661.9945

Saddle River Executive Centre,

One Route 17 South, Saddle River, NJ 07458

www.amertac.com

Made in China

MO TU WE TH FR SA SU

BLACK

RED

RDM

OFF

AUTO

*WHITE

GROUND

LOAD

Lights, Fans, Motors, etc.