AmerTac RFK106 Hızlı Başlangıç Kılavuzu

Uzaktan Kumanda AmerTac RFK106 için çevrimiçi göz atın veya pdf Hızlı Başlangıç Kılavuzu indirin. AmerTac RFK106 2 sayfaları. Wireless rf remote control system, hand held transmitter and plug-in receiver

Sayfayı Yazdır

Wireless RF Remote Control System

Hand Held Transmitter and Plug-in Receiver

Imagine turning on your house lights from inside your car. Or turning off your stereo from across the room. This wireless Radio Frequency (RF) control now

makes it possible. RF Controls are an easy, convenient way to remotely control lights, and appliances in and around your home or office. The invisible RF signal

passes through walls, doors, ceilings, floors and even around corners. Simply plug the desired appliance into the receiver and the receiver into any outlet. A

press of the button on the hand held transmitter, turns whatever you've plugged into the receiver on or off.

Channel Code Information

Three operating channels are available so you can control three separate systems at different locations in your home. Be sure to match common frequency

channels, for those devices you want operated by the same switch.

INSTRUCTIONS

Notes: The total load of appliances connected to the Plug-in Receiver should not exceed 1200

Watts or 10 Amps.

Do not use Plug-in Receiver to control appliance loads that may be dangerous to turn on

remotely (i.e. power tools).

The Plug-in Receiver must be located within 100 feet of the Wall Transmitter.

A Remove back cover of Hand Held Transmitter by pushing cover down.

A Remove plastic battery tab by gently pulling it from the battery compartment (this tab isolates

the battery until it's ready for use and insures that you'll have a fresh battery).

A Reassemble Hand Held Transmitter.

A Plug your light/appliance into the outlet on the Receiver being careful to match the wide

blade of the light/appliance (if equipped) with the wide slot on the outlet.

A Plug the Receiver into any standard grounded 110/120 Volt outlet being careful to match the

wide blade of the Receiver with the wide slot on the outlet. Fully insert.

A Hold your Hand Held Transmitter at the location where you wish to use it.

A Press Switch to determine if your light/appliance turns on and off. If your light/appliance does

not respond try relocating the transmitter or receiver. Large metal objects such as metal doors

should not be in the way of the Transmitter and Plug-in Receiver since this could decrease the

range of the RF signal.

A Attach transmitter to any key ring or place in a convenient location around the house.

OPERATION

Simply press the button on the Hand Held Transmitter to turn the light/appliance you've plugged

into the Receiver on or off.

Note: Wait at least 3 seconds after you press the transmitter on or off before you press it again.

This allows for the RF signal transmission to be completed.

BATTERY REPLACEMENT

Your RFK106 battery should last 2-3 years under normal use.

To replace battery:

A Remove back cover of Hand Held Transmitter by pushing down

on back and sliding in direction of arrow.

A Remove battery from Battery Compartment and replace with

another 12Volt battery (Radio Shack™ 23, 23M, VR22, EL22 or

equivalent).

1 Year Limited Warranty

AmerTac™ warrants this product to be free from defects in material and workmanship for a

period of 1 year from the date of purchase. AmerTac's obligations are limited to repairing or

replacing any defective units and are effective only if such units are returned within 1 year of the

purchase date, to AmerTac, 250 Boulder Drive, Breinigsville, PA 18031. Warranty void if damage

is due to accident, negligence, misuse, alteration or improper installation. In no circumstance will

AmerTac be liable for consequential or incidental damages relating in any way to this product.

Questions, ¿Preguntas?, La question? 1-800-777-0802

250 Boulder Drive

Breinigsville, PA 18031

www.amertac.com

Made in China / Hecho en China / Fabriqué en Chine

I09-0062-B

SPECIFICATIONS

240 Watts Tungsten Load, 120 Volts~, 60 Hz

Appliances up to 1200 Watts

10 Amps General Use Load, 120 Volts~, 60 Hz

Range 100 feet

Battery 12 Volt, Radio Shack™ 23, 23M, VR22, EL22

or equivalent

BACK

FCC Approved.

COVER

Plug-in receiver for indoor use only

Caution: Use of this product is licensed by the Federal

Communications Commission (FCC). Changes or

modifications not expressly approved by the party

BATTERY

responsible for compliance could void the user's

COMPARTMENT

authority to operate the equipment.

This equipment has been tested and found to comply

with the limits for a Class B digital device, pursuant to

part 15 of the FCC Rules. These limits are designed to

provide reasonable protection against harmful

interference in a residential installation. This equipment

generates uses and can radiate radio frequency energy

and, if not installed and used in accordance with the

instructions, may cause harmful interference to radio

communications. However, there is no guarantee that

interference will not occur in a particular installation. If

this equipment does cause harmful interference to radio

or television reception, which can be determined by

turning the equipment off and on, the user is encouraged

to try to correct the interference by one or more of the

following measures.

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and

• Connect the equipment into an outlet on a circuit

• Consult the dealer or an experienced radio/TV

RFK106, RFK106L

Troubleshooting Guide

SYMPTOM PROBABLE CAUSE

Light does not

1. Circuit breaker or fuse is turned

turn on.

off.

2. Switch on lamp is turned off.

3. Bulb is defective.

4. Weak battery.

5. Lamp module or lamp is loose.

Light does not

1. Transmitter signals are being

turn off.

blocked. Check for metal objects

that could block the signal, or

reposition the transmitter.

2. Switching too fast. Wait 3

seconds between toggles.

3. Weak battery.

Light comes

1. Short term power line failure.

on randomly.

2. Transmitter out of range.

3. Lamp module or lamp is loose.

the receiver.

different from that to which the receiver is connected.

technician for help.