AmerTac BL-BR33M-SW Kullanıcı El Kitabı

Işık Fikstürü AmerTac BL-BR33M-SW için çevrimiçi göz atın veya pdf Kullanıcı El Kitabı indirin. AmerTac BL-BR33M-SW 2 sayfaları. Remote controlled led rgbw under cabinet light

Sayfayı Yazdır

BL-BR33RGB-SW Owner's Manual

Location of Controls

1. ON/COLOR/OFF Switch

2. 6 Super Bright LEDs

3. Battery Compartment*

4. Magnets*

5. Slide Brackets*

6. Metal Plates*

7. 3M Adhesive Pads*

OPERATE AND CONTROL THE LIGHT TWO WAYS:

ON/OFF Switch – Once batteries are installed:

Press to turn the light ON WHITE, then again for RED,

again for GREEN, again for BLUE, again for OFF.

REMOTE CONTROL OPERATING – (On First Use, Remove Battery Compartment Protective Plastic)

The remote control unit will operate Under Cabinet Light in 65-82 feet (20-24 m) range. Once

batteries are installed, turn light ON by pointing the remote control towards the light. Use the

DIMMER, and TIMER functions by pointing the remote control towards the light and selecting the

desired function.

REMOTE CONTROL – Controls Aluminum Under Cabinet Light.

POWER - Controls Aluminum Under Cabinet Light

Turns light ON

Turns light OFF

DIMMER - Controls brightness of light

Press and hold (+) increases brightness

Press and hold (-) decreases brightness

COLOR - Chose color of LEDs

Pick WHITE, RED, GREEN or BLUE directly from the remote control. The light will remember your

color choice if you power ON again using the remote. If you power ON directly from the light, it

will always start with WHITE.

Controls the amount of time the Under Cabinet Light stay ON.

TIMER – Turn lights ON fi rst, select duration. Light will ﬂ ash once to confi rm command. Timer

clears when light turn OFF. 15, 30, 60 and 120 minutes preset.

ADDING UNDER CABINET LIGHTS TO A SET

Up to 20 lights may be controlled by one remote control. No programming is needed. Any similar

lights will be controlled when placed within the range of the remote control's signal.

MOUNTING INSTRUCTIONS

Magnetic Mounting (preferred)

The magnetic sections on the back of the light can be adjusted left to right so the corresponding

metal plates can be placed in the most ideal location for your installation.

Magnet option 1 - The metal plates come pre-drilled for easy front mounting on the desired

surface with included screws. Attached the fi rst plate to the overheads surface and check

location of second to make sure that sliding magnet will adhere to it.

Magnet option 2 - Remove protective cover from one side of the double-sided adhesive pad.

Place in center of the metal mounting plate. Do this for both metal-mounting plates. Place the

metal mounting plate with the adhesive pad onto the magnets located on the back side of

the light. Adhesive side placed away from the product (so it can stick into mounting position).

Do this for both metal-mounting plates. Remove second protective cover from adhesive tape

and place against desired surface. The metal mounting plate should be adhered to the desired

surface.

This is permanent tape that may cause damage if removed. Not recommended for use on

wallpaper or delicate surfaces.

Pulling on the light after the plates are properly installed should disconnect the metal mounting

plate from the magnets to allow for changing of batteries. The light should easily be able t o re

attached as the magnets and plates will draw to each other.

If you plan on using the light on a metal/magnetic surface, such as a cabinet, you may not need

to install the plates at all

Screw Mounting (optional)

1. Remove 2 metal plates & 2 3M Adhesive tapes from the 2 magnets on the back of the light.

2. Use Wall Anchors (not included) if securing to dry wall.

3. Measure two holes 6.75" (171 mm) apart. Drill two holes into mounting surface, insert wall

anchors (not included) and insert screws.

4. Leave screw heads out slightly so they can be inserted into the mounting holes located on

the back of the light.

5. Align and insert screw heads into mounting holes. Once inserted, slide the light onto the

screw heads to secure its position.

Product Dimensions:

Under Cabinet Light Size - 13.375" (H) x 2.25"(W) x 0.75"(D) / (340 mm x 56 mm x 19.3 mm)

Remote Size - 3.375" (H) x 1.5"(W) x 0.25"(D) / (86 mm x 40 mm x 6 mm)

Limited Warranty

Under normal use and conditions, AmerTac provides to the original purchaser of this product a one year limited

express warranty that is set forth in the Limited Warranty stated in full at www.amertac.com/warranties. The

Limited Warranty is in lieu of all other express or implied warranties or liabilities subject to the exceptions

explained fully in the Limited Warranty on the website.

8. Remote Control

9. ON/OFF Switch

10. Dimmer

11. Color Selector

12. Timer

13. Battery Compartment

*On back of unit

REMOTE CONTROLLED

LED RGBW UNDER CABINET LIGHT

INDOOR, DRY USE ONLY

BATTERY

--Each Under Cabinet Light requires 3 AA batteries (not included).

-- Remote Control requires CR2025 battery (Included)

Insert/Replacing the batteries

UNDER CABINET LIGHT – 3 AA batteries

If the LEDs appear to be dim this is an indication that the batteries need to be replaced.

- Slide off the battery compartment.

- Remove old batteries if replacing batteries.

- Insert three new AA batteries.

- Make sure to follow battery polarity guide when installing new batteries.

- Replace battery compartment housing.

REMOTE CONTROL – CR2025 battery pre-installed.

- Grip and slide battery drawer out

- Remove battery.

- Place new battery in position aligning polarity (+) (-) as indicated.

- Slide battery drawer in.

This product contains a button cell. If swallowed, it could cause severe injury or death in just 2

hours. Seek medical attention immediately.

SAFETY INFORMATION

Battery Precautions:

1. Use only the size and type of batteries specifi ed.

2. Always purchase the correct size and grade of battery most suitable for the intended use.

3. Be sure to follow the correct polarity when installing the batteries as indicated in the battery

compartment. Reversed batteries may cause damage to the device.

4. Do not mix alkaline, standard (Carbon-Zinc), or rechargeable (Nickel Cadmium) batteries.

5. Replace all batteries of a set at the same time. Do not mix old and new batteries.

6. Clean the battery contacts and also those of the device prior to battery installation.

7. Do not dispose of batteries in fi re.

8. Remove batteries if consumed or if product is to be left unused for an extended period of time.

FCC Statement

This equipment has been tested and found to comply with the limits for Part 15 of the FCC rules. These

limits are designed to provide reasonable protection against harmful interference in a residential

installation. This equipment generates, uses and can radiate radio frequency energy and, if not

installed and used in accordance with the instructions, may cause harmful interference to radio

communications.

However, there is no guarantee that interference will not occur in a particular installation. If

this equipment does cause harmful interference to radio or television reception, which can be

determined by turning the equipment off and on, the user is encouraged to try to correct the

interference by one or more of the following measures:

•

Reorient or relocate the receiving antenna.

•

Increase the separation between the equipment and receiver.

•

Connect the equipment to an outlet on a circuit different from that to which the receiver is

connected.

This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions:

(1) This device may not cause harmful interference, and (2) this device must accept any interference

received, including interference that may cause undesired operation.

Note: Modiﬁ cations to this product will void the user's authority

to operate this equipment.