Astria Fireplaces H8708 Kurulum Talimatları - Sayfa 2

Kapalı Şömine Astria Fireplaces H8708 için çevrimiçi göz atın veya pdf Kurulum Talimatları indirin. Astria Fireplaces H8708 2 sayfaları. Kits for use with envy series direct-vent gas fireplaces

Sayfayı Yazdır

INNOVATIVE HEARTH PRODUCTS • SIGNATURE SERIES DIRECT-VENT GAS FIREPLACES • ENVY TRADITIONAL • INSTALLATION INSTRUCTIONS

6. Apply a small amount of pressure against the door to hold it

in position. Then, release the two upper latches.

7. Carefully grip the glass door at the top and bottom, and

remove it from the fireplace.

NOTE: Place the glass door in a secure location where it will

not be damaged until reinstrallation.

INSTALL THE LOGS AND DECORATIVE VOLCANIC STONE

NOTE: Turn OFF all electricity to the appliance before

installing volcanic stone, and logs.

NOTE: The log set and burner are designed to provide an

artistic, asymmetrical fire. The fire does not burn in the left rear

quarter of the log set.

1. Align the two holes in the bottom of Log 1 over the two tabs

at the rear of the burner (Figure 2).

Figure 2: Placing Logs 1 and 2

f i r e - p a r t s . c o m

2. Hold Log 1 in position while placing Log 2 on the burner and

resting it against the alignment notch in Log 1 (Figure 2).

3. Place Log 3 in position with the base aligned in the burner

surface (Figure 3).

Figure 3: Placing Log 3

4. Insert the left end of Log 4 under Log 3 and position the right end

of Log 4 in the notch on the top, right end of Log 3 (Figure 4).

Innovative Hearth Products reserves the right

to make changes at any time, without notice,

in design, materials, specifications, prices and

also to discontinue colors, styles, and products.

Consult your local distributor for fireplace

Innovative Hearth Products, LLC .

P/N 900005-04 Rev. A 10/2014

P900005-04

Figure 4: Placing Log 4

5. Ensure all logs are properly positioned on the surface of the

burner and interlocked with each other (Figure 4).

6. Place Log 5 in position in the notches on the upper right

portions of Logs 1 and 3 (Figure 5).

Figure 5: Placing Logs 5 and 6

7. Place Log 6 in position in the notches near the left ends of

Logs 2 and 3 (Figure 5).

8. If Installed, position and secure the andirons.

9. Place the volcanic stone generously in front of the burner on

the ramped sub‑floor. In an artistic manner, blend the volcanic

stone with the glowing embers in front of the log set, to

simulate a diminishing ember bed.

FIREPLACE REASSEMBLY

1. With an ammonia‑free glass cleaner and soft, non‑abrasive cloth,

remove smudges from the inner surface of the glass door.

2. Carefully position the glass door in front of the firebox

with the gasket properly seated, and hook the two top door

latches over the door frame. Then, hook the two bottom

door latches over the door frame.

3. Locate the surround trim assembly mounting slots on the

left and right sides of the firebox. Align the surround trim

assembly with the mounting slots and press in and down to

lower the surround into position. Reinstall the left and right

side finish trim gap fillers.

4. With an ammonia‑free glass cleaner and a soft, non‑abrasive

cloth, remove fingerprints and smudges from the front

surface of the glass door and the surround trim assembly.

1508 Elm Hill Pike, Suite 108

Nashville, TN 37210

IHP.US.com