Astria Fireplaces H9022 Kurulum Talimatları - Sayfa 2

Şömine Aksesuarları Astria Fireplaces H9022 için çevrimiçi göz atın veya pdf Kurulum Talimatları indirin. Astria Fireplaces H9022 2 sayfaları. Glass media kit

Sayfayı Yazdır

INNOVATIVE HEARTH PRODUCTS • SIGNATURE SERIES DIRECT-VENT GAS FIREPLACES • ENVY/ENVY CD 35/40/45TEN • INSTALLATION INSTRUCTIONS

8. Carefully grip the door at the top and bottom, and remove it

from the fireplace. Place the door in a secure location where

it will not be damaged.

Figure 1: Removing the surround trim assembly

Figure 2: Upper And Lower Glass Door Latches

SCALE 0.200

f i r e - p a r t s . c o m

Hot Fireplace Will Cause

• Any attempt to use media not specified for your

fireplace configuration will result in incomplete

Severe Burns

combustion, sooting, and poor flame quality, and

will void the warranty.

Never Allow Children to

• HANDLE MEDIA ONLY WHEN COOL. Turn OFF

Touch Glass or other Fire-

all electricity to the appliance before removing

place Parts

or installing media. Media gets very HOT during

fireplace use and will remain hot up to ONE HOUR

after the gas supply is turned off.

• If media is not installed according to the installation

instructions, fl ame impingement and improper

combustion could occur, resulting in soot and/or

excessive production of carbon monoxide (CO), a

TOXIC gas that is colorless and odorless.

Innovative Hearth Products reserves the right

to make changes at any time, without notice,

in design, materials, specifications, prices and

also to discontinue colors, styles, and products.

Consult your local distributor for fireplace

Innovative Hearth Products, LLC .

P/N 900005-06 Rev. NC 10/2014

Side Tabs

Latch

WARNING

NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.

Installing the Glass Media

1. Complete the steps in Accessing the Firebox.

2. Install the glass media in the recessed area between the

front and rear floors. Spread the glass media evenly over

the designated area.

NOTE: DO NOT mound the glass media. Place a thin layer

of glass media over the burner and pilot areas (Figure 3).

NOTE: 35 in. fireplaces require less than a full bag of

glass media. 40 in. fireplaces require an entire bag. 45 in.

fireplaces require an entire bag, and may use a portion of

another bag (purchased seperately).

Figure 3: Glass Media Installed

Pilot Area

3. Complete the steps in Closing the Firebox.

Removing the Glass Media

1. Complete the steps in Accessing the Firebox.

2. Use a clean, dry, empty shop vac to remove the glass media

from the fireplace.

3. Complete the steps in Closing the Firebox.

Cleaning the Glass Media

1. Place the glass media in a colander or sieve, and carefully

rinse under hot water.

2. Spread the glass media in a thin layer on a flat surface to dry.

3. Allow the glass media to completely air dry before reinstalling.

Closing the Firebox

1. Carefully position the glass door in front of the firebox and

hook the two upper spring-loaded latches over the glass door.

Then, hook the two lower spring-loaded latches over the

glass door.

2. Use an ammonia-free glass cleaner and a soft, non-abrasive

cloth to remove fingerprints and smudges from the glass door.

3. Align the surround trim assembly with the mounting slots

along the left and right edges of the firebox and press in and

down to lower it into position. Reinstall the left and right

side finish trim gap fillers.

4. Use an ammonia-free glass cleaner and a soft, non-abrasive

cloth to remove fingerprints and smudges from the

surround trim assembly.

5. Apply electrical power and turn ON the gas supply for

the fireplace.

P900005-06

Burner Area

1508 Elm Hill Pike, Suite 108

Nashville, TN 37210

IHP.US.com