Flying Industry Development 0020057 Hızlı Kılavuz

Uzaktan Kumanda Flying Industry Development 0020057 için çevrimiçi göz atın veya pdf Hızlı Kılavuz indirin. Flying Industry Development 0020057 3 sayfaları. Rf wireless receiver

Sayfayı Yazdır
RF Wireless Receiver (Model 0020057)
Feature:
Wireless control, easy to install
Relay output, can control Lights, Motors, Fans, electrically operated Doors/Locks/Windows/Blinds/Cars or Other Appliances with AC110-240V or DC
0~28V.
You can turn on/off the receiver with transmitter (remote control) from any place within a reliable distance; the wireless RF signal can pass through
walls, floors and doors.
With characteristics of reverse power protection and over current protection
Use an 8-bit microprocessor designed and developed with low-power and high-speed CMOS technology.
Reliable control: The transmitter (Encoding) and the receiver (Decoding) use an 8-bit code.
One/several transmitters can control one/several receivers simultaneously.
If you use two or more units in the same place, you can set them with different codes.
Receiver Parameters:
Model No.: S1ST-DC06 / S1ST-DC09 / S1ST-DC12 / S1ST-DC24
Power Supply (Operating Voltage): DC6V (S1ST-DC06), DC9V±1V (S1ST-DC09), DC12V±1V (S1ST-DC12), DC24V±1V (S1ST-DC24)
Working Frequency: 315MHz / 433MHz
Channel: 1 CH
Control Modes: Toggle (Press -> On; Press again -> Off)
Output: Relay output (Normally open and normally closed)
Working Voltage Range of Relay: AC110~240V or DC0~28V
Maximum Working Current of Relay: 1A / each channel
Static Current: ≤6mA
PCB size: 45mm x 28mm x 20mm
Work with Fixed code transmitters
The receiver can pair different model transmitters, includes model C-1 (100M), CWB-1 (50M, waterproof), CP-1 (500M) and CB-1 (1000M) etc...
If you want to have a further working range, you can install an external antenna to the receiver, such as magnetic mount antenna (model 0020909),
which working range is three times as much as it used to be. Or telescopic antenna (model 0020908), which working range is twice as much as it
used to be.
Usage (with the transmitter):
Connect DC power to terminal "+" and "-".
Initial state of relay output terminals: Terminals NO and COM are Normally Open; Terminals NC and COM are Normally Closed.
1) Press the button on the transmitter: Turn on relay (connect terminals COM and NO, disconnect terminals COM and NC)
2) Press the button again: Turn off relay (disconnect terminals COM and NO, connect terminals COM and NC)
How to pair the transmitter to the receiver:
Set the same code on the receiver according to the transmitter.
How to set up the 8-bits code of the receiver:
1. Open the receiver shell, then you will see the circuit board. There are two rows pads and one row of chip feet on the back side.
2. The right row of pads is "L" side, and the left row of pads is "H" side.
3. If solder the middle row of chip feet to the "L" side, it is code 1. If solder the middle row of chip feet to the "H" side, it is code 2. Don't solder to any
side, it is code 0.
4. The 8-bits code order is from top to bottom (from D1 to D8).
5. Here is an example, the 8-bits code in the picture is 21002001, solder as the following way:
6. Code 0: don't solder any side, like D3, D4, D6, D7.
7. Code 1: solder to the "L" side, like D2, D8.
8. Code 2: solder to the "H" side, like D1, D5.
SHENZHEN GUIYUAN INDUSTRY DEVELOPMENT CO.,LTD
Http://www.carymart.com