Daedong Kioti SMV STEREO KIT Kurulum Talimatları

Araç Alıcısı Daedong Kioti SMV STEREO KIT için çevrimiçi göz atın veya pdf Kurulum Talimatları indirin. Daedong Kioti SMV STEREO KIT 2 sayfaları. For ck3510, ck3510h, ck4010, ck4010h

Sayfayı Yazdır
instaLLation
instrUctions
for for ck3510(H)/4010(H)
smv stereo kit
1. Packing List
2. generaL safety information
3. exPLoded view
4. instaLLation instrUction
d.d kit#. t2131-55452
kioti tractor division / daedong-Usa, inc.
6300 Kioti Dr. Wendell, NC 27591
Toll Free:1877-go-kioti
Tel:1-919-374-5100 Fax:1-919-374-5001
http://www.kioti.com
daedong kioti eUroPe B.v
Koerilenstraat 2, 3199LR, Maasvlakte-Rotterdam The Netherlands
Tel:+31 (0)181 35 30 25
http://www.kioti.eu
service sUPPort division / daedong indUstriaL co.,Ltd.
35, Nongongjungang-ro 34-gil Nongong-eup, Dalseong-gun, Daegu, KOREA 42984
Tel:82-53-610-3350 Fax:82-53-610-3359
http://www.daedong.co.kr
Printed in Korea. FEB. 2018
1. Packing List
no.
Part no.
description
1
TG15-0046A
ASSY,STEREO
2
T4810-82421
ANTENNA ASSY
3
T4810-82341
ASSY, SPEAKER
4
04512-50060
SPRING_WASHER
5
04013-50060
PLAIN_WASHER
6
03024-50420
SCREW_WITH_WASHER
7
03014-50625
CROSS-RECESSED HEAD MACHINE SCREW
8
02114-50060
NUT
9
T5270-55172
STEREO ACCESSORIES(MANUAL)
3. exPLoded view
(1) ASSY,STEREO
(2) ANTENNA ASSY
(3) ASSY,SPKER
(4) SPRING_WASHER
(5) PLAIN_WASHER
(6) SCREW_WITH_WASHER
(7) CROSS-RECESSED HEAD MACHINE SCREW
(8) NUT
7
2
1
Q'ty
remark
1
1
2
1
2
2
1
1
1
8
4
5
3
6
TC2SP01A
2. generaL safety information
this symbol means attention! yoUr satety is invoLved.
the message that follows the symbol contains important information
about satety. carefully read the message.
Before servicing and rePairing
3. Never use improvised tools, parts or
procedures. Use only recommended
1. Read all safety instruction in this
tools appropriate to the work.
manual and be aware of safety decal
locations on your machine.
4. Extra care should be taken to work
safely when servicing is done by two
2. Thoroughly clean your work area and
or more persons.
the machine.
5. Always support the machine with safe-
3. Make sure the machine is on firm
ty stands rated for the weight of the
and level ground and that the parking
machine. Never work under a machine
brake is set.
that is supported solely with a jack.
4. Lower the implement to the ground.
6. Do not touch any rotating or hot parts
5. Stop the engine and remove the key.
while the engine is running.
6. Disconnect the negative battery cable.
7. Escaping fluid (hydraulic oil) under pres-
7. Place a "DO NOT OPERATE" tag in
sure can penetrate the skin causing seri-
ous injury. Relieve pressure before dis-
the operator station.
connecting hydraulic or fuel lines. Tighten
all connections before applying pressure.
working safety
1. Do not operate or service the machine
disPose of fLUids ProPerLy
while under the influence of alcohol,
1. Observe relevant environmental protec-
medications, or other sustances.
tion regulations when disposing of oil.
2. Never wear loose fitting clothing and
NEVER pour fluids onto the ground,
always use safety equipment appro-
down a drain, or into any body of water.
priate to the job.
4. instaLLation instrUction
1. Park the vehicle on firm and level ground. Then, engage the parking brake and stop
the engine.
A
TC2SU02A
2. Unscrew 6 roof mounting bolts (A) to
3. Attach the antenna assembly (2) to
remove the roof.
the removed roof with Phillips screws
(7).
TC2SU03A
Next page▼