Dorma ES 200 Hızlı Başlangıç Kılavuzu

Garaj Kapısı Açıcı Dorma ES 200 için çevrimiçi göz atın veya pdf Hızlı Başlangıç Kılavuzu indirin. Dorma ES 200 4 sayfaları. Sliding door operator
Ayrıca Dorma ES 200 için: Manuel (10 sayfalar), Manuel (12 sayfalar)

Sayfayı Yazdır

DORMA

•

1. Commissioning

1.1 Please note:

Work on electrical

equipment

by properly qualified electricians.

Power supply (by others) with 16 A fuse protection

must be available.

Power cord must be double-insulated,

NYM. Do not use flat webbed house wires!

The maximum cable length of the external

components must not exceed 30 m.

1.2 Basic requirements:

• The operator is fully assembled.

• The protective earth (PE) is connected.

• The safety sensors are connected.

• Components supplied separately, such as

program switches, activators, radar motion

detectors, Night-/Sank

EMERGENCY OFF pushbuttons are installed

and connected .

• The end stops are adjusted so that both active

panels touch the end stops when the panels

have reached maximum opening width.

• When the door is closed, the active and the

passive door panel must not collide with the

sealing profiles.

• The door has to run smoothly. Check the length

of the connection screws of the toothed belt

Ij\

and replace the screws if necessary.

Lll

Update (small motor)

The ES 200 control unit can be installed as a

replacement for older systems with GR 63x25 motors.

However, a special cable for the incremental encoder

with a pulse devider is required.

The following

procedure has to be observed:

- Install hardware.

- Set program switch to "OFF" and activate the

EMERGENCY OFF pushbutton.

- Reset system to original settings (factory settings):

Press and hold service key, switch on power supply.

- Release the service key as soon as the 8 on the

seven-segment display blinks twice.

- Adjust the GR 63x25 Motor via the pushbuttons on

the basic module (b

- Unatch the EMERGENCY OFF pushbutton.

- Perform a learning cycle.

Safeguarding of door:

The safety measures to safeguard the doors must

be made in accordance with the local (country-

specific) regulations.

Where sliding doors shall be operated in Germany

DIN 18650

according to

Standard), the specifications

industrial standard must be observed.

See: WN 057015 45-5-32

Easy

ES 200

ES 200-20

ES 200 C048/

DAC 300

may only be performed

for example:

keyswitches and

0) or via PDA.

(German Industrial

stated in this

1.3 First Commissioning

1.3.1

Open the sliding panels half way.

ES200 Easy:

1.3.2

•

Set program switch to AUTOMATIC

ES200 I ES200-2D:

•

Set program switch to OFF

1.3.3

Unlatch the EMERGENCY OFF pushbutton

and bridge the light barriers. Duri ng the first

commissioning

of the system the infrared light

curtains or light barriers shall be replaced by

jumpers.(See connection diagram 056632-45532)

Following the iearning cycle, the first closing cycle

and the parameterization

of the control unit, the

infrared light curtains or light barriers have to be

connected and checked for proper functioning .

1.3.4

Insert the power plug and connect immediately

thereafter the rechargeable battery pack. (within max. 8 sec.)

The door must perform a closing cycle at low

(creep) speed.

If the door performs an opening cycle, the

system must be set back to original sellings.

Disconnect the power plug so that the opening

cycle stops.

Proceed on 2. original sellings

If the door performs a closing cycle, proceed with the

learning cycle starting with the door closed.

Please note:

The light barriers and radar motion detectors are

disabled during the learning cycle, as it has to be

performed without

interruptions.

In case that a fauit or error should occur during this

procedure, the learning cycle will be interrupted

needs to be started anew.

1.3.5

Performing the learning cycle:

ES200Easy.

press and hold SELECT button for 3 sec. Then the

door will perform a learning cycle.

ES200/ES 200-2D/ES 200 C048I DAC300:

press SERVICE button.

• Press and hold SERVICE/SELECT bullon until

the door commences with the learning cycle. The

external segments of the 7-segment display will

illuminate

in turn.

• The door accelerates in order to determine the

door weight.

• The door opens at low (creep) speed to

determine the opening width.

DORMA

and