Canyon Cottage Colors 3682802P Montaj Talimatları Kılavuzu - Sayfa 10

İç Mekan Mobilyaları Canyon Cottage Colors 3682802P için çevrimiçi göz atın veya pdf Montaj Talimatları Kılavuzu indirin. Canyon Cottage Colors 3682802P 16 sayfaları. Bunk bed

Sayfayı Yazdır
LIST OF CONTENTS
28-705 TOP BUNK END FIG.1
A.- (1) TOP BUNK BED END
HARDWARE PACK (HPK00123-0)
B.- (2) 4"METAL DOWEL PINS
28-603 LOFT DESK FIG.2
W.- (1) LOFT DESK
28-735 RAIL CAP FIG.3
D.- (1) RAIL CAP
28-766 LOFT HUTCH FIG.4
E.- (1) LOFT HUTCH
HARDWARE PACK (HPK00012-0)
B.- (2) 4"METAL DOWEL PINS
28-730 4 SIDE RLS/2 GUARD RLS FIG.5
F.- (4) SIDE RAILS
G.- (2) GUARD RAILS
HARDWARE PACK (HPK00104-0)
H.- (24) 80MM FLAT HEAD BOLTS
I.- (24) 5/16"-18 X 5/8" CROSS DOWEL NUTS
J.- (1) 5MM ALLEN WRENCH
28-709 FULL BOTTOM HDBD & FTBD FIG.6
T.- (1) HEADBOARD
U.- (1) FOOTBOARD
HARDWARE PACK (HPK00127-0)
V.- (4) CASTERS
28-720 LADDER FIG.7
N.- (1) LADDER
HARDWARE PACK (HPK00008-0)
O.- (2) METAL HOOK BRACKETS
P.- (6) 1" SCREWS
28-706 TWIN BUNKBED ENDS FIG.8
S.- (1) 1 PC BUNK BED END TWIN
TOP BUNK BED
1.- ASSEMBLE
2.- TAKE LOFT DESK (W), AND PLACED IT IN THE ROOM'S DESIRED POSITION, PLACE IT FACING OUTWARDS.
3.- INSERT TWO DOWEL PINS (B ) ON TOP IN EACH OUTSIDE CORNER OF LOFT DESK (W ), TAKE THE LOFT HUTCH (E), AND PLACE IT ON TOP OF LOFT DESK ALIGNING METAL
DOWEL PINS WITH EACH PRE-DRILLED HOLE IN BOTH ENDS UNTIL THE METAL DOWEL PINS ARE ALL IN,
4.- INSERT TWO CROSS DOWEL NUTS (I) IN ACCESS HOLE INSIDE SIDE RAIL & GUARD RAIL, ALIGN CROSS DOWEL NUT MAKE SURE THE GROOVE IS HORIZONTAL, (FIG.A)
5.- ATTACH TWO SIDE RAILS AND TWO GUARD RAILS TO DESK/HUTCH/TOP BUNK BED ASSEMBLY AND 1 PC BUNK BED END TWIN (S ), INSERTING TWO FLAT BOLTS (H ) INTO
TOP BUNK BED AND 1 PC BUNK BED END TWIN HOLES, USE ALLEN WRENCH TO TIGHTEN BOLTS,
CONNECTED TOGETHER)
6.- PLACE FOUR SLATS (Q) ON TOP SIDE RAIL CLEATS, ONE SLAT IN BOTH ENDS, PUSH THE SLAT AGAINST THE BED END POST (FIG.B) AND TWO SLATS IN THE MIDDLE AT
EQUAL DISTANCE FROM THE END SLATS, THEN EACH SLAT MUST BE FASTEN WITH TWO 1 1/4" SCREWS (S), SEE FIG.12
FIG.10
FRONT
REV 04 05/08/2019
CANYON FURNITURE COMPANY
TWIN OVER FULL LOFT BUNK WITH LOFT DESK ASSEMBLY INSTRUCTIONS
N
S
100-645/646 TWIN/FULL SLATS FIG.9
, USING ONE TOP BUNK BED END (A), ONE LOFT DESK (W), ONE LOFT HUTCH (E), TWO SIDE RAILS (F), AND TWO GUARD RAILS (G).
FIG.11
,
FIG.11
HARDWARE PACK
A
HPK00123-0
B
FIG.1
HARDWARE PACK
E
HPK00012-0
B
FIG.4
HARDWARE PACK
HPK00008-0
P
O
FIG.7
FIG.9
HARDWARE PACK
HPK00016-0
Q
FIG.8
Q.- (4) SLATS
HARDWARE PACK (HPK00016-0)
R.- (8) 1 1/4" SCREWS
( DO NO TIGHTEN COMPLETELY UNTIL ALL PIECES ARE
FIG.12
FIG.11
PAGE 2 OF 4
W
FIG.2
F
G
FIG.5
T
R
TOOLS NEEDED
PHILIPS HEAD SCREWDRIVER (NOT INCLUDED)
5MM ALLEN WRENCH (INCLUDED)
SEE FIG.10
FIG.B
D
FIG.3
HARDWARE PACK
HPK00104-0
H
J
I
U
FIG.6
HARDWARE PACK
HPK00127-0
V
YES,
HORIZONTAL
GROOVE
NO
FIG.A
KIS01179-2C