Dot-Spot side-light Operatör El Kitabı - Sayfa 2

Peyzaj Aydınlatması Dot-Spot side-light için çevrimiçi göz atın veya pdf Operatör El Kitabı indirin. Dot-Spot side-light 2 sayfaları.

Sayfayı Yazdır

object-light

Thank you!

Thank you very much for buying the dot-spot object-light or the dot-

spot side-light! dot-spot products are developed and manufactured

according to very high quality guidelines. The high quality and long life

of the products are an active contribution to resource conservation

and environmental protection.

Read the instructions completely before using the object-light or

side-light. Keep this manual in a safe place. In case you forward the

object-light or side-light towards third persons, also give them the

operating instructions. Failure to follow these instructions may cause

danger to persons and damage to property. We will not assume any

liability for damage to persons and property resulting from failure to

follow these instructions.

Technical description

The dot-spot object-light and the dot-spot side-light are recessed

luminaires with a fixed 2 W Power LED. The body is completely made

of aluminium. The protection class is IP 64 and permits indoor and

outdoor use. object-light and side-light are directly connected to volt-

age source of 230 V rated voltage. The installation is done in in-wall

boxes with 55 mm in diameter, deep design. object-light and side-light

can be installed in walls and ceilings. They are used for illuminating

staircases, paths, walls, porches and objects.

Configurations

object-light and side-light are available in different configurations:

Colour:

aluminum, gray anodized, painted white

Body shape (e.g. sidelight):

round cover plate

Fluorescent colours:

white, approx. 6500 K

Installation

With screws in deep flush-mounted or cavity boxes with Ø 55 mm.

Technical data

Rated voltage

Power

Luminosity

Safety class

Body

Cover

Safety instructions:

During installation, the relative safety regulations have to be followed.

The installation may only be carried out by appropriately trained

professionals.

object-light and sight-light are operated at a voltage of 230 V. To avoid

danger, prior to any work at the object-light and side-light, separate the

supply cable from the mains by switching off the corresponding fuse.

The luminaires may only be installed by an electrician.

A wrong tension may destroy the luminaire. Connect the luminaire to

power supply systems with the required voltage only.

High ambient temperatures shorten the life of the LED. To ensure a

long life of the LED, a good heat dissipation has to be ensured. There-

fore, do not use the object-light and side-light at ambient temperatures

> 50°C. Do not cover the luminaire.

object-light and side-light may only be operated using the round or

square cover plate included. Removing the cover plate will void the

warranty, because high temperatures can occur and may shorten the

life span of the LED.

In the event of the luminaires being installed outdoors, you should

make sure that no water can penetrate the socket. For this purpose, a

gasket ring is included. In case of very rough wall surfaces, additional

sealing measures are necessary.

The luminaires should be used in protected/roofed outdoor areas only.

Avoid permanent heavy wetness or direct solar radiation.

Never look directly into the light beam.

Preparation:

Unpack all the parts included in delivery and check them for complete-

ness and intactness. The scope of delivery contains:

■

Luminaire object-light or side-light with cover plate

■

2 screws, suitable for the screw holes of standard in-wall boxes

■

Gasket

■

Instructions for use and installation

Dispose of the packaging material no longer needed in accordance with

applicable regulations. If you notice any damage from transport, please

immediately contact the dealer from which you purchased the luminaire.

Installation:

1. Separate the supply line from the mains by switching off the fuse.

Protect the fuse from switching it on again.

2. Connect the connecting wires to the corresponding wires of the

supply line using suitable terminals.

Clamp the phase conductor L (brown or black) of the in-wall box

and the phase conductor (brown) of the luminaire together.

clamp the neutral conductor (blue) of the in-wall box and the

neutral conductor (blue) of the luminaire together.

clamp the protective conductor (yellow-green) of the in-wall box

and the protective conductor (yellow-green) of the luminaire together.

3. Now fix the luminaire to the in-wall box using the two screws in-

cluded. The outdoor installation requires inserting the rubber

gasket (included) between cover plate and wall.

Important: If you purchased the side light, make sure that the light

orifice points towards the surface to be illuminated. If necessary,

you can turn the luminaire towards the desired position by

loosening the spring ring.

4. Now, reconnect the in-wall box to the mains by switching on the fuse.

dot-spot information for the user

LED lights are extremely energy efficient and, under normal operation,

have a very long life. Therefore, the replacement of the lamp is not

provided. To ensure the maximum life of the LED, the following should

be considered:

1. The heat dissipation of the LED must not be hindered. Therefore,

do not cover the luminaire.

2. Avoid operating the luminaires in case of direct solar radiation.

3. In automatic mode, control the luminaires via timer and twilight

switch.

4. Clean the luminaires from time to time with a damp cloth.

5. Immediately replace broken lenses.

Disposal

At the end of the useful life, dispose of the lamp and all accessories in

accordance with the applicable environmental regulations. Electrical

waste must not be disposed of with domestic waste.

Terms of warranty in Germany

These terms of warranty apply since 2006/01/01 - Technical changes

reserved. These terms of warranty apply to the purchase and use of

our products in the Federal Republic of Germany. In other countries

the warranty conditions will be those stipulated in the terms of sales

and shipment for the respective country or by law.

All dot-spot products are thoroughly checked and tested before leaving

the factory. However, the occurrence of occasional failures during

operation may not be excluded.

In accordance with legal provisions, we grant a 2-year warranty and a

manufacturer's warranty of another 3 years from the date of purchase

(invoice receipt). This warranty refers to the proper function of the dot-

spot products and accessories under normal conditions of use.

The warranty does not cover damages resulting from normal wear or

mechanical destructions by outside forces. The legal warranty rights

are not affected by this warranty. This warranty statement is our

voluntary service as manufacturer.

The warranty covers replacement of defective parts. There shall be

no entitlement to the compensation for consequential damages. In

particular, there shall be no right to reimbursement of consequential

damages resulting from improper use or improper installation of the

products. The professional installation is described in the installation

instructions.

dot-spot GmbH & Co. KG

Entwicklung – Produktion – Vertrieb

Industriestraße 1a

90592 Schwarzenbruck

Germany

Phone +49 9128 / 72 22 17 - 0

Fax

+49 9128 / 72 22 17 - 9

[email protected]

www.dot-spot.de

Operator's Manual | dot-spot object-light / side-light |

10101GA Rev. 3 | January 2021

Bedienungsanleitung

Operator's Manual

100 - 240 V / 50 Hz

approx. 2 W

object-light: ww 124lm; kw 179 lm

side-light: ww 48 lm; kw: 69 lm

IP 64 (front side)

Aluminium

Aluminium, natural, anodised or painted white

80 mm

60 mm

21 mm

3 mm

Akzente setzen!

side-light

square cover plate

warm white, approx. 3000 K

80 mm

60 mm

38 mm

Tiefe 27 mm

32 mm

30 mm

80 mm