Dot-x DNR V SERIES Kullanıcı Kılavuzu - Sayfa 8

Monitör Dot-x DNR V SERIES için çevrimiçi göz atın veya pdf Kullanıcı Kılavuzu indirin. Dot-x DNR V SERIES 10 sayfaları. 25 inch display
Ayrıca Dot-x DNR V SERIES için: Kullanıcı Kılavuzu (12 sayfalar)

Sayfayı Yazdır

INSTALLERS MENU ADJUSTMENTS

To access the Installer's Menu, press and hold the MENU key until the User Menu

display disappears, then press 9876, (this may take a couple tries) and then

ENTER to access the Installer's Menu.

1390-04

Microcontroller

Part Number

03HPos9

Build Date

10/04/00

The black bar near the top of the screen indicates the part number of the software

in the display. To the right is a number indicating that the module has been tested.

The date on the black bar near the bottom of the screen indicates the date the

module went through the factory.

When the Installer's menu appears, it displays the third Service Menu item:

POWER MANAGE. Use the Up/ Down Arrow keys to toggle through all of the

adjustments. Use Left/Right Arrows to make a change to the

00 FACT MENU: Use SELECT UP and DOWN Keys to select item 00, the Factory

Mode. This item is used by the Factory when the module is being tested. It has two

positions: 0 and 1. In the field, this item should always be left off (Zero is off).

When this item is off, only the first twenty-four items in the Installer's Menu can be

accessed. They appear one at a time near the middle left of the screen. When this

item is set to 1, 81 menu items are available.

In the Factory Menu, only the selected menu item is displayed, near the top of the

screen, as shown in the figure above.

When the Factory Menu is on, the AC Power-On feature is always enabled

regardless of the setting of AC ON in the Installer's Menu. The display will

automatically come on when AC is applied.

Use the remote to reenter the Installer's Menu to turn the Factory Menu off. The

Factory Mode may also be turned off by setting the clock, or running the Auto

Program feature in the customer Set Up menu.

01 PRESET PX: Stores the video customer menu adjustments in the nonvolatile

memory of the EAROM. Selections are Custom and Preset-Store. Settings for

Contrast, Brightness, Color and Tint are stored in this manner. 0 is custom and 1

is Preset stored.

02 PRESET AX: Stores customer Audio menu adjustments in the nonvolatile

memory of the EAROM. Selections are Custom and Preset-Store. Settings for

Bass, Treble, Balance and SoundRite are stored in this manner. 0 is custom and

1 is Preset stored.

2.08

Program

Font

Revision

Factory Option

TE Status

TE=10110000

HARC MENU

CHANGING SECURITY CODE AND UNIT NUMBER

The security code and the unit number can be changed with the remote control.

First it is necessary to enter the current security code and unit number, refer

to GETTING STARTED earlier in this manual for the procedures to enter the

security code and unit number.

Press and hold the 0 (zero) key until the following screen appears

(typically 6-8 seconds).

KEY NEW 4 DIGIT SECURITY CODE

THEN PRESS ENTER KEY

If you do not wish to change the security code, pressing ENTER does not allow

you to escape. If you wish to change the code, key in the new code. As you

key in numbers, x's will appear on the screen. When you have keyed in 4

digits, the screen will change as follows.

KEY NEW 4 DIGIT SECURITY CODE

THEN PRESS ENTER KEY

KEY NEW CODE AGAIN TO CONFIRM #

THEN PRESS ENTER KEY

At this point, you must key in the new number again or key in the current code

if you wish to retain the current code. Then press the ENTER key. This saves

the new code and makes it active for all future operations requiring the security

code.

Retain the new security code in a safe place for future reference.

The following on screen display (OSD) will appear.

KEY NEW 2 DIGIT UNIT ID NUMBER

THEN PRESS ENTER

xxxx