Electra Light Atomic 3000 DMX Kullanıcı Kılavuzu - Sayfa 9

Aydınlatma Ekipmanları Electra Light Atomic 3000 DMX için çevrimiçi göz atın veya pdf Kullanıcı Kılavuzu indirin. Electra Light Atomic 3000 DMX 10 sayfaları. Strobe 3000 dmx professional lighting

Sayfayı Yazdır
DMX
CONTROL
SUMMARY
For specific command values, see ''DMX protocols" on page 20.
INTENSITY
Flash intensity can be set from minimum (blackout) to maximum on channel 1 in
the 3- and 4-channel DMX modes. Intensity is maximum in 1-channel DMX
mode.
The maximum intensity can be reduced by selecting low power mode
as described on
page ......
DURATION
Flash duration can be set from 0 to 650 ms on 50
ms on 60
Hz
power supplies, on channel 2 in
Flash duration is fixed in 1-channel DMX mode.
RATE
Flash mte can be set from 0 flashes
per
second to 25 flashes per second
Hz
power supplies, or from 0 to 30 flashes per second on 60
on channel 3 in the 3-
and
4-channel DMX modes. Flash mte is also controllable
in 1-channel DMX mode.
PROGRAMMED EFFECTS
Six progmmmed effects are available on channel 4 in the 4-channel DMX mode
only.The effects may be altered using the intensity, duration, and rate controls.
Ramp up:Light gradually increases in intensity,then blacks out.
Ramp down:Light flashes to full intensity,then gradually fades.
Ramp up-down: Light gradually increases and decreases.
Random flash:Light flashes randomly with variable rate and
intensity.Multiple unite flaah independently
Lightning: The flashea simulate lightning.Duration is not adjustable.
Splkea: The lamp remains dimly Illuminated between flashes.Set
flash intenaity,duration,and rate as normal.
BLINDER
EFFECT
The blinder effect, in which the light remains on for an extended period, is
available
in
all DMX modes.
In
the 3- and 4-channel modes, the effect is achieved
11
Hz
power supplies, or 0 to 530
the
3- and 4-<:hannel DMX modes.
Hz
on 50
Hz
power supplies,
of
each other.

CONTROLLER OPERATION

This section
describes how to operate the Strobe 3000 with
DATA
CONNECTION
The Strobe 3000 provides both 3-pin and 5-pin
data connection. The pin-out on all sockets is pin 1
and
pin
3 to hot(+). There is no connection to pins 4 and
parallel: both inputs connect
irrput
and
output/
Olle
Olle
To connect the data link
1
Connect the DMX data input from the controller to the
S-pin input {male) aoc:ket.
2
Connect up to 31additional fiXtures output-to-input.
3
Insert a termination plug in the output of the last fixture on the link.
DATA CONNECTION TIPS
Use shielded twisted-pair cable designed for RS-485 devicea: standard
microphone cable cannot transmit controldata reliably over long runs.24
AWG cab le is suitable for runs up to 300 meters (1000
cable and/or an amplifier tor longer runs.
Never use both outputs to split the link.To split the seriallink into
branches use a signalsplitter.
Do not overload the link.Up to 32 devices may be connected on a seriallink.
Terminate the link by installing a termination plug in the output socket of the
last fixture. The termination plug,which Is a male XLR plug with a 120 ohm,
0.25
watt
resistor soldered betwaen pins 2 and 3, "soaks
signalso It does not reflect and cause Interference.
Use a phaseoftYersing cab le to connect older
reversed polarity sockets (pin 3 cold).
a
DMX controller.
XLR
sockets
shield, pin 2 to cold
to
5.
The sockets are wired in
to
For reliable data transmission use
both
outputs.
Strobe
3DOD 's 3-pin or
ft.).
Use heavier gauge
up"
the control
Metight
fixtures with
8
for
(-),