Dover PSG ALL-FLO A100 Kurulum Operasyon ve Bakım - Sayfa 3

Su Pompası Dover PSG ALL-FLO A100 için çevrimiçi göz atın veya pdf Kurulum Operasyon ve Bakım indirin. Dover PSG ALL-FLO A100 20 sayfaları. Plastic 1/4 inch air-operated double-diaphragm pump
Ayrıca Dover PSG ALL-FLO A100 için: Kurulum Operasyon ve Bakım (19 sayfalar)

Sayfayı Yazdır

Dover PSG ALL-FLO A100 Kurulum Operasyon ve Bakım

CAUTIONS — READ FIRST!

READ THESE WARNINGS AND SAFETY PRECAUTIONS PRIOR TO

INSTALLATION OR OPERATION. FAILURE TO COMPLY WITH THESE

INSTRUCTIONS COULD RESULT IN PERSONAL INJURY AND OR

PROPERTY DAMAGE. RETAIN THESE INSTRUCTIONS FOR FUTURE

REFERENCE.

WARNING

Pump, valves and all containers must be properly

grounded prior to handling flammable fluids and/or whenever static

electricity is a hazard.

WARNING

Prior to servicing the pump, ensure that the air and

fluid lines are closed and disconnected. While wearing personal protective

equipment, flush, drain and process liquid from the pump in a safe manner.

WARNING

The TX marking refers to the maximum surface

temperature depending not on the equipment itself, but mainly on

operating conditions. In this case, the maximum surface temperature

depends upon the temperature of the process fluids.

WARNING

For pump models with non-metallic manifolds,

air valves, or chambers: When the relative humidity in the surrounding

atmosphere is above 30%, the equipment must not be touched by

personnel unless first wiped down with a damp cloth.

WARNING

Maintenance must not be performed when a

hazardous atmosphere is present.

WARNING

Use only with liquid process fluid.

WARNING

This equipment's ambient temperature range is

32°F (0°C) to 104°F (40°C)

WARNING

Do not operate the pump with fluids or in

temperatures which are less than 32°F (0°C)

CAUTION

The temperature of the process fluid and

air input must be no more than 36°F (20°C) less of the maximum

temperature allowed for the appropriate non-metallic material. See the

list of temperatures below for each material's maximum recommended

temperature:

Buna-N (Nitrile):

Geolast

EPDM:

Santoprene

FKM:

PTFE:

Polyethylene:

Polypropylene:

PVDF:

Nylon:

Temperature limits are solely based upon mechanical stress and certain

chemicals will reduce the maximum operating temperature. The allowable

temperature range for the process fluid is determined by the materials

in contact with the fluid being pumped. Consult a chemical resistance

guide for chemical compatibility and a more precise safe temperature

limit. Always use minimum air pressure when pumping at elevated

temperatures.

ALF-11010-E-01

10°F to 180°F (-12°C to 82°C)

-40°F to 280°F (-40°C to 138°C)

-40°F to 225°F (-40°C to 107°C)

-40°F to 350°F (-40°C to 177°C)

40°F to 220°F (4°C to 104°C)

32°F to 158°F (0°C to 70°C)

32°F to 180°F (0°C to 82°C)

0°F to 250°F (-18°C to 121°C)

0°F to 200°F (-18°C to 93°C)

WARNING

= Hazards or unsafe practices which

could result in severe personal injury,

death or substantial property damage

CAUTION

= Hazards or unsafe practices which

could result in minor personal injury,

product or property damage.

CAUTION

It is the end user's responsibility to maintain the

process fluid's temperature during use.

CAUTION

Do not connect a compressed air source to the

exhaust port of the pump.

CAUTION

Do not lubricate air supply.

CAUTION

Do not exceed 120 psig (8.3 bar)

air-inlet pressure.

CAUTION

Do not exceed 10 psig (0.7 bar)

or 23 ft-H

O suction pressure.

CAUTION

Ensure all wetted components are chemically

compatible with the process fluid and the cleaning fluid.

CAUTION

Ensure pump is thoroughly cleaned and flushed

prior to installation into a process line.

CAUTION

Always wear Personal Protective Equipment (PPE)

when operating pump.

CAUTION

Close and disconnect all compressed air and bleed

all air from the pump prior to service. Remove all process fluid in a safe

manner prior to service.

CAUTION

Blow out all compressed air lines in order to

remove any debris, prior to pump installation. Ensure that the muffler is

properly installed prior to pump operation.

CAUTION

Ensure air exhaust is piped to atmosphere prior to a

submerged installation.

CAUTION

Ensure all hardware is set to correct torque values

prior to operation.

CAUTION

The equipment must be inspected for visible

damage prior to use.

WARNING

This product can expose you to chemicals including

Nickel, Chromium, Cadmium, or Cobalt, which are known to the State of

California to cause cancer and/or birth defects or other reproductive harm.

For more information, go to www.P65Warnings.ca.gov.

SECTION

All-Flo