Dover Hydro AccuPro Hızlı Başlangıç Kılavuzu - Sayfa 2
Dağıtıcı Dover Hydro AccuPro için çevrimiçi göz atın veya pdf Hızlı Başlangıç Kılavuzu indirin. Dover Hydro AccuPro 2 sayfaları. Proportioner with airgap eductors
Ayrıca Dover Hydro AccuPro için: Hızlı Başlangıç Kılavuzu (2 sayfalar), Hızlı Başlangıç Kılavuzu (2 sayfalar), Hızlı Başlangıç Kılavuzu (2 sayfalar), Hızlı Başlangıç Kılavuzu (2 sayfalar)
Sayfayı Yazdır
Metering Tip Selection:
The fi nal concentration of the dispensed solution is re-
lated to both the size of the metering tip opening and
the viscosity of the liquid being siphoned. For water-thin
products, the chart at left can be used as a guideline. If
product is noticeably thicker than water, consult the Mea-
surement of Concentration Procedure below to achieve
your desired water-to-product ratio. Because dilution can
vary with water temperature and pressure, actual dilution
achieved can only be ascertained by using the Measure-
ment of Concentration Procedure. The clear, undrilled tip
is provided to permit drilling to size not listed should you
need a dilution ratio that falls between standard tip sizes.
NOTE: A 1 GPM eductor is grey; a 4 GPM eductor is yellow.
Refer to parts diagram if unfamiliar with names of system
components.
Measurement of Concentration:
You can determine the dispensed water-to-product
ratio for any metering tip size and product viscosity.
All that is required is to operate the primed dispenser
for a minute or so and note two things: the amount of
dispensed solution, and the amount of concentrate used
in preparation of the solution dispensed.
Dilution Ratio (X:1) where X = Amount of Mixed Solution — Amount of Concentrate Drawn
Dilution Ratio, then, equals X parts water to one part concentrate (X:1). If the test does not yield the desired ratio, choose a diff erent tip
and repeat the test. Alternative methods to this test are 1) pH (using litmus paper), and 2) titration. Contact your concentrate supplier
for further information on these alternative methods and the materials required to perform them.
AccuPro Select Parts Diagram List:
5
6
7
APPROXIMATE DILUTIONS
AT 40 PSI FOR WATER-THIN PRODUCTS (1.0 CP)
Tip
Orifi ce
Std. Drill
Ratio (per Eductor Flow)
Color
Size
Number
1 GPM
3.5 GPM
No Tip
.187
(3/16)
2.6:1
Grey
.128
(30)
2.6:1
Black
.098
(40)
2.5:1
Beige
.070
(50)
3:1
Red
.052
(55)
5:1
White
.043
(57)
7:1
Blue
.040
(60)
9:1
Tan
.035
(65)
11:1
Green
.028
(70)
17:1
Orange
.025
(72)
19:1
Brown
.023
(74)
22:1
Yellow
.020
(76)
32:1
Aqua
.018
(77)
39:1
Purple
.014
(79)
64:1
Pink
.010
(87)
128:1
Amount of Concentrate Drawn
2
1
4
3
9
Key
Part No.
Description
1
238100
Strainer washer
2
10082830 Swivel collar (molded)
3
10082801 Swivel stem (molded)
4
10075911 Hex nipple
8
10075950 O-ring (two per nipple)
5
10075926 Pipe plug
6
10091035 Wall bracket
7
10093995 Cabinet
8
10020700 Selector valve grommet
10020900 Back up ring for grommet
9
10093710 Button, dark grey
10
10075980 Valve parts kit
a. diaphragm, b. armature,
c. spring, d. valve bonnet
11
10079010 Spring
12
10079000 Magnet
13
10075986 Water valve
AccuPro Select Parts Diagram:
4:1
4:1
5:1
13
8:1
13:1
22:1
26:1
14a
34:1
52:1
64:1
71:1
102:1
128:1
213:1
447:1
15a
16a
Key
Part No.
14a 160
b 161
15 a 10070170 1 GPM inner discharge tube
b 10070470 3.5 GPM inner discharge tube
16 a 10064794 1 GPM outer discharge tube
b 10077310 3.5 GPM outer discharge tube
17
10080957 Selector replacement kit:
18
10080720 Hose hook, grey, for
19
3401-R
20
690014
21
500814
500821
22
509900
23
10089410 Footvalve, viton (EPDM also
NOT SHOWN:
641751
10
a
b
c
d
11
12
17
e
f
g
19
Description
1 GPM eductor assembly
3.5 GPM eductor assembly
e. support clip, f. Suction stub,
g. O-ring, h. selector valve assembly
3.5 GPM discharge tube
Hosebarb
Metering tip (kit)
Tubing, 1/4" x 14'
Tubing, 1/4" x 21'
Weight
available order 10076302)
Screws (cabinet sides)
3.5 GPM EDUCTOR (RIGHT SIDE)
14b
19
20
21
22
15b
23
16b
18