Follett F505A/W Kullanım, Servis ve Parça Kılavuzu - Sayfa 4
Su Sebili Follett F505A/W için çevrimiçi göz atın veya pdf Kullanım, Servis ve Parça Kılavuzu indirin. Follett F505A/W 17 sayfaları. Ice and water dispenser
Ayrıca Follett F505A/W için: Kurulum Kılavuzu (13 sayfalar)
Sayfayı Yazdır- 1. Operation
- 2. Troubleshooting
- 3. Before Calling for Service
- 4. Troubleshooting Sensorsafe Board and Sensors
- 5. Wiring Diagrams
- 6. Dispense Chute and Splash Panel Areas - Lever Models
- 7. Dispense Chute and Splash Panel Areas - Sensorsafe Models
- 8. Wheel Motor and Drive System
- 9. Hopper Components
- 10. Solenoid Dispense Assembly
4. Remove dispense mechanism.
5. Wipe lid, wheel, baffle, inside of storage area and dispense mechanism with damp cloth wrung out in Solution A.
To avoid possible damage to motor assembly, use a damp cloth only. Do not allow water to
!
run through center hole in bottom of bin area.
6. Rinse all above items with damp cloth rinsed and wrung out in clear water.
7. Sanitize all above items with damp cloth wrung out in Solution B. Do not rinse.
8. Pour 1 cup (284ml) household bleach into drain pan, followed by 1 gallon (3.8L) of hot tap water to flush drains.
9. See Dispense Wheel Removal section for proper spacing of baffle and reinstall parts.
10. If unit is equipped with chilled water accessory, also see below.
If dispenser is equipped with chilled water accessory:
1. Remove two (2) screws securing splash panel and lay splash panel on dispenser drain pan.
2. Disconnect 3/4" drain line from bottom of chilled water canister.
3. Loosen (do not remove) screw securing front bracket of chilled water canister to bottom of dispenser hopper.
4. Rotate canister to left to release front bracket, then pull canister forward to disengage rear bracket.
5. Remove chilled water coil from canister and clean with cloth wrung out in Solution A.
6. Wipe inside of chilled water canister with cloth wrung out in Solution A.
7. Rinse all above items with damp cloth wrung out in clear water.
8. Sanitize all above items with damp cloth wrung out in Solution B. Do not rinse.
9. Reinstall chilled water coil into canister (rubber alignment grommet on coil tubing must be located outside chilled
water canister to hold coil securely against canister wall).
10. Reinstall chilled water assembly on dispenser and tighten screw securing front bracket.
11. Reconnect 3/4" drain line to chilled water canister.
12. Reinstall splash panel and top front cover.
13. Restore power and test operation.
Quarterly cleaning of icemaker system
Units with icemakers require icemaker cleaning at least every 3 months, and more often if local water conditions
dictate. Failure to clean icemaker will result in decreased performance and potential damage to icemaker. Refer to
Icemaker Operation and Service Manual for specific cleaning instructions.
Troubleshooting
Disconnect power to dispenser and icemaker before putting hands or arms in storage area
!
or attempting any repair or service to equipment.
Before calling for service:
• Check that there is ice in dispenser bin area
• Check that congealed cubes are not causing a jam
Symptom
1. Does not dispense
ice
Possible cause
a. Power switch off or faulty.
b. Faulty dispense switch.
c. Wheel motor malfunction.
d. Drive chain off.
e. Sprocket key missing.
f. Faulty dispense solenoid.
Service
• Check that all switches and circuit breakers are on
• Check that all drains are clear
a. Check switch. Turn on or replace if faulty.
b. Replace switch.
c. Check motor and replace as required.
d. Reinstall chain.
e. Install key and tighten sprocket.
f. Check solenoid and replace if faulty.
4
Solution