Bosch ASCENTA SHX6AP Kullanım ve Bakım Kılavuzu - Sayfa 18
Bulaşık Makinesi Bosch ASCENTA SHX6AP için çevrimiçi göz atın veya pdf Kullanım ve Bakım Kılavuzu indirin. Bosch ASCENTA SHX6AP 26 sayfaları. Bosch ascenta models dishwashers use & care manual
Ayrıca Bosch ASCENTA SHX6AP için: Kullanım ve Bakım Kılavuzu (21 sayfalar), Kullanım ve Bakım Kılavuzu (21 sayfalar)
Sayfayı Yazdır
10
Depending on your model you will either have 4, 5 or 6 wash
cycles.
To start the dishwasher:
•
Open the Door. Press the "ON/OFF" button.
•
One of the Wash Cycle LEDs will be flashing. You can
now select a wash cycle.
•
Press the "<" or ">" button to select the desired wash
cycle.
•
Press the "START" button (LED stops flashing)
•
Close the door to begin the cycle
NOTE
1.
Rinse Agent Indicator Light will be illuminated if the
unit needs Rinse Agent.
2.
If you close the door without pressing the start button
the unit will beep.
To cancel a cycle:
•
Open the dishwasher door just far enough to expose
the control panel. Be careful of hot water splash out!
•
Press and hold the "START/RESET" button until the
"Active" indicator light goes out.
WARNING
You could be seriously scalded if you allow hot water
to splash out of the dishwasher. OPEN THE DOOR
CAREFULLY during any wash or rinse cycle. Do not fully
open the door until water noises have stopped.
•
Close the door and wait for about 1 minute for the
dishwasher to drain.
•
The unit will beep when done draining.
•
Open the door and press the "ON/OFF" button.
•
You are now ready to start a new cycle.
To enter the options mode (rinse agent setting, ex-
tra dry heat, cycle completion signal):
•
Door must be open. Press the "ON/OFF" button to
turn the unit on.
•
One of the Wash Cycle LEDs will be flashing.
•
Press and hold down the ">" button, then press and
release the "START/RESET" button. Now release the
">" button.
18
Operating the Dishwasher
SHX4AP, SHX5AL, SHX6AP
•
The "Clean" and one other LED will be flashing. You
are now in the options setup mode.
•
Press ">" to select the option you would like to
adjust.
If the "Clean" and "Rinse Agent" LED are flashing you can
adjust the Rinse Agent settings.
If the "Clean" and "Sanitized" LED are flashing you can set
the Extra Dry Heat.
To set the amount of Rinse Agent:
NOTE: If your glasses have spots on them, you need more
rinse agent. If your glasses have streaks, you need less
Rinse Agent.
Follow the prior instructions to enter "options" mode.
With the "Clean" and "Rinse Agent" LEDs flashing:
•
Press the "<" button to change the amount of rinse
agent dispensed.
0 LEDs flashing --> Rinse Agent dispenser is OFF
1 LED flashing --> Lowest amount of rinse agent
2 LEDs flashing --> Medium amount dispensed
3 LEDs flashing --> Highest amount of rinse agent
•
Press
"START" to save your settings.
To turn Extra Dry Heat on or off:
With the "Clean" and "Sanitized" LEDs flashing:
•
Press the "<" button to turn Extra Dry Heat on or off.
The wash cycle LEDs will illuminate when you press
"<".
0 LEDs flashing --> Extra Dry Heat is OFF
1 LED flashing --> Extra Dry Heat is ON
To set the Cycle Completion Signal:
With the "Clean" , "Sanitized" , and "Rinse Agent" LEDs
flashing:
•
Press the "<" button to change the cycle completion
tone level. The wash cycle LEDs will illuminate when
you press "<".
0 LEDs flashing --> Cycle Completion Signal is OFF
1 LED flashing --> Low tone level
2 LEDs flashing --> Medium tone level
3 LEDs flashing --> Highest tone level
•
Press
START to save your settings.