Bosch FAP-OC 500Series Kurulum Kılavuzu - Sayfa 11

Bulaşık Makinesi Bosch FAP-OC 500Series için çevrimiçi göz atın veya pdf Kurulum Kılavuzu indirin. Bosch FAP-OC 500Series 28 sayfaları. Built-in wall ovens
Ayrıca Bosch FAP-OC 500Series için: Kurulum Talimatları Kılavuzu (21 sayfalar), Kullanım Kılavuzu (40 sayfalar), Kurulum Kılavuzu (6 sayfalar), Ürün Bilgileri (40 sayfalar), Kullanıcı Kılavuzu (48 sayfalar), Kullanıcı Kılavuzu (48 sayfalar), Kurulum Kılavuzu (28 sayfalar), Kullanım ve Bakım Kılavuzu (44 sayfalar), Kurulum Kılavuzu (32 sayfalar), Kullanım ve Bakım Kılavuzu / Kurulum Talimatları (40 sayfalar), Hızlı Referans Kılavuzu (4 sayfalar), Kullanım ve Bakım Kılavuzu (27 sayfalar), Kurulum Kılavuzu (24 sayfalar), Kurulum Kılavuzu (32 sayfalar), Kullanım ve Bakım Kılavuzu (24 sayfalar), Kurulum Kılavuzu (28 sayfalar), Servis Kılavuzu (41 sayfalar), Kullanım ve Bakım Kılavuzu (21 sayfalar), Kurulum Kılavuzu (32 sayfalar), Servis Kılavuzu (36 sayfalar), Kurulum Kılavuzu (32 sayfalar), Hızlı Başlangıç ve Güvenlik Kılavuzu (13 sayfalar)

Sayfayı Yazdır

Replace the blower plate and secure with the screws

removed in Step 1.

Attach the exhaust adapter to the rear of the oven by

sliding it into the guides. Push in securely until it is in

the lower locking tabs. Make sure the damper hinge

swings freely.

Preparing cabinet

Remove power to outlet.

Remove all contents from upper cabinet.

Tape the TOP CABINET TEMPLATE onto the bottom

surface. Make sure the template centerline aligns with

the vertical line on the wall. Rear wall arrows must be

against rear wall.

Note: For recessed cabinet bottom, trim the template

edges so that it fits inside the recessed area. The

template has trim lines to use as guides.

Drill 3\8" (10 mm) holes at "A", "B" and "C".

Note: Wear safety goggles when drilling holes in the

cabinet bottom.

Cut out the 2" (51 mm) hole at "D". This hole is for the

power supply cord.

Note: If the cabinet is metal, use the nylon grommet

around the opening to protect the cord.

Roof venting installation only: Cut out the shaded

area "E" on the TOP CABINET TEMPLATE using a

saber or keyhole saw.

Remove templates from back wall and cabinet.

Mounting the microwave oven

Notes

If the bottom of the upper cabinet is recessed or has

▯

front overhang, you will need to prepare 2" x 2" (51

mm x 51 mm - depth equivalent to cabinet recess or

overhang) filler blocks to provide additional support for

the bolts:

mark the center of each filler block and drill a 3\8"

▯

(10 mm) diameter hole

align filler blocks over the three openings on top of

▯

the microwave oven and attach with masking tape

Use at least two people to install the microwave oven.

▯

Do not grip or use handle during the installation.

When mounting the microwave oven, thread power

▯

cord through hole in bottom of top cabinet. Keep the

cord tight and do not pinch it, especially when

mounting flush to bottom of cabinet. Do not pull the

cord to lift the oven.

Lift the microwave, tilt it forward, and hook slots at

back bottom edge onto four lower tabs of the

mounting plate.

Rotate the front of the oven up against cabinet bottom.

Insert a self-aligning screw (item A) through top center

cabinet hole. Temporarily secure the oven by turning

the screw at least two full turns after the threads have

engaged.