Bosch SGE63E15UC Kurulum Talimatları Kılavuzu - Sayfa 4
Bulaşık Makinesi Bosch SGE63E15UC için çevrimiçi göz atın veya pdf Kurulum Talimatları Kılavuzu indirin. Bosch SGE63E15UC 40 sayfaları. 24" recessed handle special application
Ayrıca Bosch SGE63E15UC için: Kurulum Talimatları Kılavuzu (38 sayfalar), Ek (2 sayfalar), Kullanım Talimatları Kılavuzu (40 sayfalar), Kullanım Kılavuzu (40 sayfalar), Kullanım Talimatları Kılavuzu (44 sayfalar), Broşür ve Teknik Özellikler (3 sayfalar), Kullanım Talimatları Kılavuzu (40 sayfalar)
Sayfayı Yazdır
Avoiding General Hazards
Do not use the dishwasher until it is completely
installed. When opening the door on an uninstalled
dishwasher, carefully open the door while supporting
the rear of the unit. Failure to follow this warning can
cause the dishwasher to tip over and result in serious
injury.
Before installing the "L"-shaped supplied counter-
top mounting brackets (select models), decide which
method will be used to secure the dishwasher into its
opening. Once these mounting brackets are installed
on the dishwasher, removing them is difficult and will
damage the mounting brackets and the dishwasher.
In some conditions, hydrogen gas can form in a
hot water system that has not been used for weeks.
Hydrogen gas is explosive.
Before filling a dishwasher from a system that has
been off for weeks, run the water from a nearby faucet
in a well ventilated area until there is no sound or evi-
dence of gas.
Temperatures required for soldering and sweating will
damage the dishwasher's base and water inlet valve.
If plumbing lines are to be soldered or sweated, keep
the heat source at least 6 inches (152.4 mm) away from
the dishwasher's base and water inlet valve.
Removing any cover or pulling the dishwasher from the
cabinet can expose hot water connections, electrical
power and sharp edges or points. Handle with care.
Avoiding Electrical Shock/Fire Hazards
Do not allow the electrical and water supply lines to
touch. Separate channels are provided under the dish-
washer.
Do not work on an energized circuit. Doing so could
result in serious injury or death. Only qualified electri-
cians should perform electrical work. Do not attempt
any work on the dishwasher electric supply circuit
until you are certain the circuit is de-energized.
Make sure electrical work is properly installed. There
should be no loose electrical connections. Ensure all
electrical connections are properly made.
3
WARNING
The customer has the responsibility of ensuring that the
dishwasher electrical installation is in compliance with
all national and local electrical codes and ordinances.
The dishwasher is designed for an electrical supply
of 120V, 60 Hz, AC, connected to a dishwasher-
dedicated, properly grounded electrical circuit with
a fuse or breaker rated for 15 amps. Electrical supply
conductors shall be a minimum #14 AWG copper only
wire rated at 75°C (167°F) or higher.
This appliance must be connected to a grounded
metal, permanent wiring system, or an equipment-
grounding conductor must be run with the circuit
conductors and connected to the equipment-
grounding terminal or lead on the appliance. Do not
use extension cords.
Improper connection of the equipment-grounding
conductor can result in a risk of electric shock. Check
with a qualified electrician or service representative
if you are in doubt whether the appliance is properly
grounded. Do not modify the plug provided with the
appliance, if it will not fit the outlet, have a proper
outlet installed by a qualified electrician.
Avoiding Plumbing/Scalding Hazards
Do not perform any work on a charged hot water
line. Serious injury could result. Only qualified
plumbershould perform plumbing work. Do not
attempt any work on the dishwasher hot water supply
plumbing until you are certain the hot water supply is
shut off.
Do not over tighten the 90° elbow. Doing so may
damage the water inlet valve and cause a water leak.
Temperatures required for soldering and sweating
will damage the dishwasher's water inlet valve. If
plumbing lines are to be soldered or sweated, keep
the heat source at least 6 inches (152.4 mm) away from
the dishwasher's water inlet valve.
Check local plumbing codes for approved plumbing
procedures and accessories. All plumbing should be
done in accordance with national and local codes.
These instructions depict an installation method for
stainless steel braided hose or PEX hot water supply
lines. If using copper tubing or other material for
water supply, defer to a licensed plumber for proper
installation.