DRAKE DQT861 Kullanım Kılavuzu - Sayfa 8
Modülatör DRAKE DQT861 için çevrimiçi göz atın veya pdf Kullanım Kılavuzu indirin. DRAKE DQT861 15 sayfaları. Digital to qam transcoder; multiplexing qam modulator
Sayfayı Yazdır
8
Setup and Programming
Programming and viewing of the various setup and
operating parameters is accomplished using the front panel
back lit, two line, sixteen character wide LCD along with
the 4 arrow buttons and the ENTER button. The name of
the parameter is on the top line of the display and the
setting value is on the bottom line.
To observe a certain parameter setting without intending to
change its value, just use the left and right arrow buttons to
navigate through the menus shown in the list. The current
setting for each parameter is shown on the bottom line of
the display. Note that depending upon certain settings,
some screens are not needed and will be skipped.
To make a change in the displayed parameter and its
setting and if this is the initial setup, you will want to enter
the 'adjust' mode. To do this, press the ENTER button that
is located in the center of the four arrow buttons and hold
in for several seconds until the display begins to flash.
After you are in the adjust mode (bottom line of screen
flashing) use the left and right arrows to navigate among
screens and use the up and down arrows to change the
parameter setting. When ENTER is pressed, the new
settings will be loaded and stored and the unit will exit the
'adjust' mode. You may wish to not press ENTER until you
have gone through all screens and settings and then
press ENTER to save and load all changes in one step
OR you can store just one or several parameters at a time
and reenter adjust mode to set the next. Either method is
acceptable.
Menu Item
Parameter Setting Choices
Top display line.
Second display line.
Use left/right arrows Must be in adjust mode to change
to navigate.
using up/down arrows.
Demod A ChanMap: CATV
DQT
IRC
HRC
Broadcast
Demod A Channel:
#
DQT
Demod A Mode:
VSB-8
DQT
VSB-16
QAM-16A
QAM-32A
QAM-64A
QAM-128A
QAM-256A
QAM-64B
QAM-256B
Demod A SymRate: Preset ( If Preset, Sym Rate is...
DQT
5.381119 for VSB modes
5.000000 for all QAM-A
5.056841 for QAM-64B
5.360537 for QAM-256B)
Manual
Demod A SymRate: x.xxxxxx (Only if Manual)
DQT
MULTIPLEX:
Disabled
DQT, MQM
Demod B
ASI
MPEG PROGRAMS:
Select All Programs
(MULTIPLEX is not
Select Programs
disabled)
(See details on pages 9 & 10)
Demod B ChanMap: CATV (Only if Demod B Enabled)
DQT
IRC
HRC
Broadcast
Demod B Channel:
# (Only if Demod B Enabled)
DQT
Demod B Mode:
VSB-8 (Only of Demod B Enabled)
DQT
VSB-16
QAM-16A
QAM-32A
QAM-64A
QAM-128A
QAM-256A
QAM-64B
QAM-256B
Demod B SymRate: Preset (Only if Demod B Enabled)
DQT
(If Preset, Sym Rate is...
5.381119 for VSB modes
5.000000 for all QAM-A
5.056841 for QAM-64B
5.360537 for QAM-256B)
Manual
SymRate:
x.xxxxxx (Only of Demod B Enabled)
DQT
(Only if Manual)
Input B Offset:
0 (Only if Multiplex Enabled)
DQT, MQM
10
20
30
40
50
60
70
80
90
PSIP:
Enabled
DQT, MQM
Disabled
Basic MGT & VCT
VCT TABLE:
TVCT (Only if Multiplex Enabled)
DQT, MQM
CVCT
Major Channel:
Original (Only if Multiplex Enabled)
DQT, MQM
RF Channel