Bosch 300 Series Kullanım ve Bakım Kılavuzu / Kurulum Talimatları - Sayfa 16

Yıkayıcı Bosch 300 Series için çevrimiçi göz atın veya pdf Kullanım ve Bakım Kılavuzu / Kurulum Talimatları indirin. Bosch 300 Series 40 sayfaları. Built-in wall ovens
Ayrıca Bosch 300 Series için: Kullanım Kılavuzu (40 sayfalar), Kullanıcı Kılavuzu (21 sayfalar), Kurulum Kılavuzu (6 sayfalar), Kurulum Kılavuzu (36 sayfalar), Kurulum Kılavuzu (32 sayfalar), Kullanım Talimatları Kılavuzu (50 sayfalar), Hızlı Başlangıç ve Güvenlik Kılavuzu (7 sayfalar), Kurulum Kılavuzu (28 sayfalar), Hızlı Başlangıç Kılavuzu (7 sayfalar), Kullanım ve Bakım Kılavuzu (32 sayfalar), Hızlı Başlangıç ve Güvenlik Kılavuzu (7 sayfalar), Servis Kılavuzu (36 sayfalar), Hızlı Başlangıç ve Güvenlik Kılavuzu (13 sayfalar)

Sayfayı Yazdır
Bosch 300 Series Kullanım ve Bakım Kılavuzu / Kurulum Talimatları
Open the connection box toward the rear of the
3.
appliance by removing the T20 torx head screw
fastening the cover.
Remove the 4-wire power cord (as supplied):
4.
A. Remove the 3 Philips screws (2 labeled L and one
labeled N).
B. Remove the green grounding screw PE (T20 torx).
NOTICE: Be careful not to drop the screws into the
dryer.
Loosen the strain relief clamp screw (Philips head) on
5.
rear of the connection box.
Pull the old power cord out of the connection box.
6.
Install the new power cord back through the strain
7.
relief clamp.
NOTICE: Ensure the strain relief clamp has not been
moved and its clamping screw(s) are outside the rear
of the connection box.
Ensure the terminal ends are long enough and are
8.
formed (bent) so that no part of them (wires or
terminal ends) come in contact with connection box
enclosure.
NOTICE: Use only open-end spade lugs.
Ensure the terminal ends are long enough and are
9.
formed (bent) so they will align with the terminal block
fastening locations (screw holes).
Reinstall the 2 terminal block screws (Philips head) at
10.
locations L as shown below.
If the ground wire shown below from N to PE is not
11.
part of the 3-wire cord assembly you have it must be
obtained/purchased separately and it must be
installed.
16
Install the last terminal block screw (Philips) and 1
12.
grounding screw (T20 torx) at locations N and PE.
Tighten the strain relief screw ensuring the power cord
13.
cannot be pulled out of the connection box but not so
tight as cut the power cord insulation.
Reinstall the connection box cover making sure all
14.
wires are routed so they do not touch any part of the
enclosure and are secure.
Reinstall the appliance top cover as previously
15.
described in "2" above.
Integrated electrical receptacle
This appliance is equipped with a 208/240V 15A
receptacle for use ONLY with Bosch washer.
CAUTION
9
Do not use this receptacle to power any other
device.
If any other electrical device is plugged into this
receptacle Bosch assumes no liability.
CAUTION
9
Use integrated electrical receptacle only for 208/
240V Bosch washers.