Dranetz-BMI ES220 Kullanım Talimatları Kılavuzu - Sayfa 2

Monitör Dranetz-BMI ES220 için çevrimiçi göz atın veya pdf Kullanım Talimatları Kılavuzu indirin. Dranetz-BMI ES220 16 sayfaları. Multifunctional power monitor

Sayfayı Yazdır
Brief description
The ES20/ES220 are panel mounting instruments for monitoring
AC systems with dimensions 96 x 96 mm (ES20) and 44 x 44 mm
(ES220). The following measurements are acquired: voltages, currents,
frequency, and phase angles in single phase or 3 phase systems. From
these, the active power, reactive power, apparent power, active energy,
reactive energy, and the power factor and the neutral current can be cal-
culated. With the use of voltage and current transformers, the instrument
can be used for measurements in medium and high voltage systems.
The transformation ratios are configurable for the direct display of all
measurements. The ES20/ES220 instrument is used as a display with
two S0 pulse or limit value outputs.
Technical data
(for more detailed information please see data sheet, download under
www.camillebauer.com)
Measuring inputs
Nominal frequency:
Nominal input voltage:
Nominal input current:
Continuous overload withstand
0 A at 346 V single phase AC system
0 A at 600 V three phase system
Short duration overload withstand
Number of
Input variable
applications
577 V LN
0
00 A
0
00 A
5
Measuring ranges
U, I, S:
P, Q:
F:
cosϕ:
Pulse/Limit value outputs
Depending on the function selected, the two digital outputs can be used
either as pulse outputs for active and reactive energy or as limit signals.
The outputs are passive, and are galvanically isolated from all the other
circuits by opto-couplers. They are suitable to drive tariff devices (S0-
standard DIN 43 864) or 24 V-relais.
U
≤ 40 V DC
(OFF: leakage current ≤ 0. mA)
ext
I
≤ 50 mA
(ON: terminal voltage ≤ .2 V)
L
Limit value outputs
Any measured value can be allocated to the limit values.
Impulse outputs
Active and reactive energy impulses can be generated for driving elec-
tronic and electromechanical energy meters.
2
50, 60 Hz
Phase-phase: 500 V
Phase - N: 290 V
5 A or A
Duration
Interval
of
between
overload
two overloads
s
0 s
s
00 s
3 s
5 min
≤ 20% of nominal value
≤ ± 20% of nominal value
45 to 65 Hz
±
Power supply*
DC, AC power pack 45 to 400 Hz
85 to 253 V AC/DC or 20 to 70 V AC/DC
Power input:
* For power supplies > 25 V the auxiliary circuit should include an
external fuse.
Reference conditions acc. to IEC 688 resp. EN 60 688
Sine 50 - 60 Hz, 5 - 30°, application group II
Measurement accuracy (related to nominal value)
Current, voltage
Power
Power factor
Energy
Frequency
Environmental conditions
Operating temperature:
Storage temperature:
Relative humidity:
Altitude:
Indoor use statement
Safety
Protection class:
Measuring category:
Pollution degree:
Measurement voltage:
Test voltage:
Module connections:
Enclosure protection:
Note of maintenance
No maintenance is required.
Display
The measurement display is 3 digit resp. 4 digit (frequency) and right
justified, with the exception of the energy values which are 8 digits. The
left-hand 7-segment display is for the sign or an abbreviation.
Abbreviations:
Maximal value
Minimal value
Average value
Max. average value
Minimal value for power factor; the worst out of the 3 values
of P, P2, or P3 is displayed
Neutral current
Inductive
Capacitive
Incoming
Outgoing
Interval active power
Interval reactive power
Interval apparent power
Last interval; t-0
,
... Previous interval; t-, -2, -3, -4
Overload, out of range indicator
≤
System value
≤
Delta voltage
< 3 VA (without extension module)
± 0.5%
± .0%
± .0%
± .0%
± 0.02 Hz (abs.)
-0 to +55 °C
-25 to +70 °C
≤ 75%
2000 m max.
II (voltage inputs with protection
impedances)
III
2
300 V
Between current inputs, power
supply, digital outputs, terminals
of the plugged-in module: 3700 V /
50 Hz / min.
At voltage inputs:
4.25 kV .2/50 µs
The pin rail at the back is connected
to the voltage inputs via a protec-
tion impedance. Only the permitted
modules can be plugged-in!
Front IP 66, terminals IP 20