Draper 220V Signature V Series Kurulum ve Kullanım Talimatları
Projeksiyon Perdesi Draper 220V Signature V Series için çevrimiçi göz atın veya pdf Kurulum ve Kullanım Talimatları indirin. Draper 220V Signature V Series 2 sayfaları. Electric
Sayfayı Yazdır
220V Signature/Series E & V Electric Projection Screen
These Installation/Operating Instructions are available in the official language of the
country where you purchase the product. Please contact your distributor to request a
copy.
Vous pourriez demander les instructions d'installation et d'opération traduises
dans la langue officielle du pays ou vous achetez le produit. Veuillez demander à votre
distributeur.
Die Gebrauchsanweisung für Installation und Konstruktion sind in der offiziellen
Sprache des Landes, indem Sie das Produkt gekauft haben, vorhanden. Fragen Sie die
jeweilige Verkaufs-Abteilung.
1 Read instructions through completely before proceeding. Follow instructions care-
fully. Installation contrary to instructions invalidates warranty.
2 Pick up screen case from ends only. Picking case up at other points will damage
case and may damage fabric.
3 To insure a safe installation, the entire weight of the unit MUST BE supported by
the end-plates.
4 Entire bottom of screen case should be unobstructed to permit proper operation of
automatic trap door, and access to bottom panel for making electrical connections
or servicing.
5 Screen should be installed level (using a carpenter's level).
6 Nothing should be fastened to screen dowel, viewing surface or automatic trap door.
7 Operating switch(es) packed separately in screen carton. Do not discard with
packing material.
8 Screen operates on 220V AC, 50 Hz. current.
NOTE: Screen has been thoroughly inspected and tested at factory and found to be
operating properly prior to shipment.
These instructions are meant as a guide only. They do not imply any responsibility on
the part of Draper, Inc. for improper installation or faulty workmanship at the jobsite.
Hanging Screen
When locating viewing surface and checking clearance for screen's operation,
remember that the surface is centered in case. Screen is normally recessed above
ceiling and may be installed in a variety of ways. See details on back of this sheet.
Regardless of mounting method used, the following points apply:
Keep case level when lifting and mounting. Pick up screen case from ends
only. Picking case up at other points will damage case & may damage fabric.
➁ Screen should be positively and securely supported so that vibration or even
abusive pulling on viewing surface will not weaken installation.
➂ Installer must insure that fasteners used are of adequate strength and suitable
for the mounting surface chosen.
➃ Entire bottom of case must be readily accessible after installation.
➄ The hinge that connects bottom panel and automatic trap door of screen must
be permitted to operate freely. Front and back of case must be straight—not
forced to warp or bow. Hinges must be free from mastic or paint buildup, and
doors must be unobstructed by ceiling tiles.
➅ Do not use screen case to support adjacent sections of ceiling.
➆ If trim pieces must be attached to case, do not permit screws to protrude more
than 6.35mm thru 3.2mm wall of case. Do not attach trim pieces with nails.
➇ If case is painted, slots on bottom of case should be shielded to protect
viewing surface from paint splatters or overspray.
➈ Do not seal unit in ceiling until electrical connections have been made and
screen has been operated successfully.
3
/
" (9.5mm)-16 threaded rod
8
(use for suspending
screen) by others.
5
/
" (8mm)-18 threaded rod
16
(use for adjusting
deflection) by others.
3
/
" (9.5mm) -16 threaded rod
8
(use for suspending
screen) by others.
®
Copyright © 2013 Draper Inc. Form Signature220V_Inst13
Installation/Operating Instructions
Caution
Case support
brackets. NOT
for use in
supporting
weight of case.
Brackets installed with rivets at factory.
Bracket spacing:
• Small Case Construction /E or /V
-Case length <95"-no brackets required
-Case length >95"-1 bracket centered
• Large Case Construction /E or /V
-2 brackets equally spaced
Printed in U.S.A.
Screen operates on 220V AC, 50 Hz., 1 ph. current. Junction box is located
just above the access plate at left end of screen. Access plate is held closed
with flathead screws and may be opened with a Phillips screwdriver. Automatic
trap door does not need to be opened to make field connections. Junction box
contains pigtail leads and grounding screws, per wiring diagram on reverse.
Screen is shipped with internal wiring complete and control switch(es) fully boxed.
Wire connecting screen to switch(es) and switch(es) to power supply should be
furnished by installer. Connections should be made in accordance with attached
wiring diagram, and wiring should comply with National and local electrical codes.
All operating switches should be "OFF" before power is connected.
CAUTION—Important Instructions—Signature/Series V—The shipping sup-
port brackets must be removed from each end of dowel during initial operation
before screen is operated in UP direction. After screen is installed, run viewing
Dowel (Series V)
surface DOWN to access screws that hold brackets to dowel. Loosen hex head
screw, remove bracket and retighten screw at each end of dowel. Signature/Series
E—The protective paper wrapping around the viewing surface must be removed
before the screen is operated in down direction. Cycle viewing surface down and
up several times to confirm satisfactory operation. If viewing surface or trap door
do not operate properly, turn power off and free trap door and/or check electrical
connections.
220V Single Station Control—3-position UP-OFF-DOWN switch permits opera-
tion to be stopped at any point. Factory set limit switches automatically stop screen
when fully down or fully up.
220V Multiple Station Control (Not CE Approved)—Switches are similar in ap-
pearance to Single Station Control. Screen stops when switch is released and may
be restarted in either direction. Factory set limit switches stop screen automatically
when fully down or fully up.
24V Control—Three-button UP-STOP-DOWN switches stop at any point desired,
operate in any sequence. Factory set limit switches automatically stop screen
when fully down or fully up. Wireless controls—whether infrared or radio fre-
quency—interface with low voltage control box.
Key Operated Switching (Not CE Approved)—Two kinds of key-operated
switches are optionally available with this unit. The key-operated power supply
switch controls power to the screen and switches. When it is "off", the switches will
not operate screen. Key may be removed from the switch in "on" or "off" position.
➁ A three-position key switch permits the screen to be operated directly by key. In
this case, the screen's operator must have a key.
RS232/Ethernet—Serial communication and network communication optionally
available with wall switches, RF or IR remote.
Please Note: Screen limits are factory set for optimum performance of the
screen. A procedure is outlined below for minor tweaks, but any adjustment
of these limits may negatively affect the flatness of the screen surface and
could also void the warranty. Please check with Draper prior to resetting
screen limits.
CAUTION: Always be prepared to shut screen off manually when new
adjustment is being tested. Screen may be severely damaged if viewing
surface is allowed to run too far up or too far down.
CAUTION: Be sure all switches are in "off" position before adjusting limit
switches.
Adjusting "Fully Up" Position—"Up" stopping position may be adjusted by turn-
ing the yellow llimit switch adjustment socket. The yellow socket is located on left
end of screen roller and is accessible to a screwdriver/Allen wrench (4mm or
Turning the socket counterclockwise will allow the viewing surface to retract further
into the case. Turning it clockwise will cause the surface to stop further out of the
case. One full revolution of the socket will alter the stopping position of the viewing
surface by approximately 3.8 cm.
Adjusting "Fully Down" Position—"Down" stopping position may be adjusted by
turning the white limit switch adjustment socket. The white socket is located on the
left end of screen roller and is accessible to a small flat screwdriver/Allen wrench
(4mm or
/
"). Turning the socket counterclockwise will allow the viewing surface
5
32
to run farther down. Turning it clockwise will shorten the viewing surface, causing it
to stop in a less extended position. At no time should viewing surface be unrolled
enough to expose any part of the screen roller.
Please note: See page 2 for information on adjusting Tab-Tensioning cables on
Signature/Series V screens.
If you encounter any difficulties installing or servicing your Signature screen, call your
dealer or Draper, Inc. Spiceland, Indiana, U.S.A., (765) 987-7999, FAX (765) 987-1689.
Electrical Connections
Operation
Shipping Support Bracket
Adjustments
US Patent No.
5,341,241
/
").
5
32