Draper Access MultiView Series Kurulum ve Kullanım Talimatları

Projeksiyon Perdesi Draper Access MultiView Series için çevrimiçi göz atın veya pdf Kurulum ve Kullanım Talimatları indirin. Draper Access MultiView Series 4 sayfaları. 220 volt electric projection screen & masking system

Sayfayı Yazdır

Access/MultiView Electric Projection Screen & Masking System by Draper

These Installation/Operating Instructions are available in the official language

of the country where you purchase the product. Please contact your distributor

to request a copy.

Vous pourriez demander les instructions d'installation et d'opération traduises

dans la langue officielle du pays ou vous achetez le produit. Veuillez

demander à votre distributeur.

Die Gebrauchsanweisung für Installation und Konstruktion sind in der

offiziellen Sprache des Landes, indem Sie das Produkt gekauft haben,

vorhanden. Fragen Sie die jeweilige Verkaufs-Abteilung.

1 Read instructions through completely before proceeding.

2 Follow instructions carefully. Installation contrary to instructions invali-

dates warranty.

3 Entire bottom of screen case should be unobstructed to permit access

to bottom panel for making electrical connections or servicing.

4 Screen should be installed level (using a carpenter's level).

5 Nothing should be fastened to screen dowel, viewing surface, or

masking.

6 Operating switches packed separately in screen carton. Do not discard

with packing material.

7 Screen operates on 220V AC, 50 Hz., 1 ph current.

NOTE: Screen has been thoroughly inspected and tested at factory and

found to be operating properly prior to shipment.

Hanging Screen

When locating viewing surface and checking clearance for screen operation,

remember surface is centered in the length of the case. Regardless of mount-

ing method used, the following points apply:

1 Mounting brackets are packed separately in carton. Engage each

bracket with top of housing as shown below and tighten set screws. A

bracket should be within 46 cm of each end of screen case. Brackets

can be removed and case mounted with lag screws through top of case

(holes drilled on site).

2 Screen should be positively and securely supported so that vibration or

even abusive pulling on viewing surface or masking will not weaken

installation.

3 Installer must insure that fasteners used are of adequate strength and

suitable for the mounting surface chosen. Supporting hardware (chains,

cables, rods, etc.) must be essentially vertical.

4 Entire bottom of case must be readily accessible after installation is

complete.

Remove shipping brackets

before operating screen.

Slots along top of case permit

brackets to be set at an angle

Typical Installation

Alternate

Installation

(additional

set of

brackets

required but

not included)

Case dimensions

on page 4.

220 Volt Installation/Operating Instructions

Caution

Shipping

Bracket

Printed in U.S.A.

US Patent Nos. 6,137,629; 6,421,175; 6,532,109; 6,816,308; 7,559,707

5 Front, back and top of case must be straight—not forced to warp or bow.

6 If case is painted on location, removal of roller/fabric assembly is recom-

mended prior to painting. If not removed, slot on bottom of case should be

shielded to protect viewing surface from paint splatters or overspray.

7 Do not seal unit in ceiling until electrical connections have been made

and screen has been operated successfully.

Screen operates on 220V AC, 50 Hz., 1 ph current.

All connections are made in the junction box located just above the bottom

access panel at left end of screen. Remove the bottom access panel for ac-

cess to the junction box cover. (See Bottom Access Panel Removal instruc-

tions below).

Remove four (4) hex head screws that secure the cover to the junction box to

expose two sets of brown, black, and blue pigtail leads and the green ground

wire per wiring diagram on page 4.

If optional low voltage control or video interface control is specified and factory

installed for either motor, please refer to wiring diagram on page 3.

Screen is shipped with internal wiring complete and control switch(es) fully

boxed. Wire to connect screen to switch(es) and switch(es) to power supply

should be furnished by installer. Connections should be made in accordance

with attached wiring diagram, and wiring should comply with national and

local electrical codes.

All operating switches should be "off" before power is connected.

Bottom Access Panel Installation/Removal

Bottom access panel hooks over the lower inside edge of the screen housing

and then is pivoted downward until the engagement brackets on each end of

the bottom panel click into place with the ball detents on each endcap. Make

sure bottom access panel clicks in place at each end of its length.

With bottom access panel

Dowel

angled up approx. 20 degrees,

engage hook on the panel

with lip of the housing

Remove bottom access panel by pushing up at each corner of panel

adjacent to slot in bottom of the housing. With bottom access panel angled

up approximately at 20° it can be lifted off of the lip of the housing and then

lowered out of the housing completely.

Electrical Connections

Using the hook and lip as a pivot,

pull the panel downward until the

engagement brackets click into

place with the ball detent

on each endcap

Engagement bracket

(one on each end of the

bottom access panel)

Bottom flange of Access housing

Bottom access panel pushup

points for panel removal

Caution: Beware of pinch

points at ends of closure

Access case as seen from below