AirStage ASHA07GACH Kurulum Kılavuzu - Sayfa 10

Klima AirStage ASHA07GACH için çevrimiçi göz atın veya pdf Kurulum Kılavuzu indirin. AirStage ASHA07GACH 15 sayfaları. Indoor unit (wall mounted type)
Ayrıca AirStage ASHA07GACH için: Kullanım Kılavuzu (6 sayfalar)

Sayfayı Yazdır

3 Remote controller address

3-wire type

Rotary switch (RC AD SW)...Factory setting "0"

When connecting multiple indoor units to 1 standard wired remote controller, set

the address at RC AD SW in sequence from 0.

Setting

Setting range

Remote controller

0 to 15

address

Example

If 4 indoor units are connected.

Indoor unit

RC AD SW

Remote

controller

RC AD SW

Address

RC AD SW

Address

ii) 2-wire type

Rotary switch (RC AD SW)...Factory setting "0"

Since the remote controller address settings are automatically conﬁ gured, you do

not need to conﬁ gure them.

If conﬁ guring manually, it is necessary to conﬁ gure both the indoor unit and the

remote controller. For details, please refer to the remote controller manual.

6.2. Custom code setting

Selecting the custom code prevents the indoor unit mix-up.

(Up to 4 codes can be set.)

Perform the setting for both the indoor unit and the remote controller.

Confusion

Indoor

unit

Remote

controller

Custom code setting for indoor unit

Set the DIP switch SET 3 SW1, SW2 referring to the Table B.

DIP switch (SET 3)

OFF

SW1

SW2

SET 3

SW3

SW4

Table B

A (Factory setting)

DIP switch

OFF

SET 3 SW1

DIP switch

OFF

SET 3 SW2

6.3. Switching the upper limit of cooling

temperature

This setting can be raised the upper limit of the cooling temperature setting range.

This setting can be used when connecting to the following controllers.

• Wired remote controller (2-wire type)

• Central remote controller

• Touch panel controller

• System controller

• Service tool

• Web monitoring tool

En-9

Type of switch

Setting

example

RC-AD

Indoor unit

RC AD SW

Code change

Controller PCB

Custom code

OFF

DIP switch setting

Set the DIP switch SET 4 SW3 referring to the Table C.

DIP switch (SET 4)

OFF

SW1

SW2

SW3

SW4

Table C

DIP switch SET 4 SW3

OFF (Factory setting)

NOTE:

Please do not make a standard setup and an extension setup intermingled in remote

controller group.

6.4. Function Setting

• FUNCTION SETTING can be performed with the wired or wireless remote controller.

(The remote controller is optional equipment)

• Refer to the wired or wireless remote controller manual for detailed setting information.

(Set IU AD, REF AD SW to 0)

• Refer to "6.1. Setting the address." for indoor unit address and refrigerant circuit address

settings.

• Turn the power of the indoor unit ON before starting the setting.

* Turning on the power to the indoor units initializes EEV, so make sure the piping air

tight test and vacuuming have been conducted before turning on the power.

* Also check again to make sure no wiring mistakes were made before turning on the

power.

Function details

Function

Filter

indicator

interval

Filter

indicator

action

Cool air

temperature

trigger

Heat air

temperature

trigger

Auto restart

Cool Air

Prevention

External

control

Error report

target

Fan setting

when cooling

thermostat

OFF

SET 4

Cooling temperature setting range

Setting number

Default

number

○

Default

Longer

Shorter

○

Enable

Disable

Display only on

central remote

controller

○

Default

Adjust (1)

Adjust (2)

○

Default

Adjust (1)

Adjust (2)

Adjust (3)

Enable

○

Disable

○

Super low

Follow the

setting on the

remote controller

○

Start/Stop

Emergency

stop

Forced stop

○

All

Display only on

central remote

controller

Follow the setting

○

on the remote

controller

Stop

Controller PCB

Standard (18 to 30 °C)

Extension (18 to 32 °C)

Details

Adjust the ﬁ lter cleaning interval noti-

ﬁ cation. If the notiﬁ cation is too early,

change to setting 01. If the notiﬁ cation

is too late, change to setting 02.

Enable or disable the ﬁ lter indica-

tor. Setting 02 is for use with a

central remote controller.

Adjust the cool air trigger temperature.

To lower the trigger temperature,

use setting 01. To raise the trigger

temperature, use setting 02.

Adjust the heat air trigger temperature.

To lower the trigger temperature by 6

degrees C, use setting 01. To lower the

trigger temperature by 4 degrees C, use

setting 02. To raise the trigger tempera-

ture, use setting 03.

Enable or disable automatic sys-

tem restart after a power outage.

Restrain the cold airﬂ ow with mak-

ing the airﬂ ow lower when starting

heating operation. To correspond

to the ventilation, set to 01.

Allow an external controller to start

or stop the system, or to perform an

emergency stop.

* If an emergency stop is performed

from an external controller, all refriger-

ant systems will be disabled.

* If forced stop is set, indoor unit stops

by the input to the external input

terminals, and Start/Stop by a remote

controller is restricted.

Change the target for reporting errors.

Errors can either be reported in all

locations, or only on the wired remote.

When set to 01, the fan stops when

the thermostat is OFF in cooling

operation. Connection of the wired

remote controller (2-wire type or 3-wire

type) and switching its thermistor are

necessary.