Draper Clarion Montaj/Montaj Talimatları
Projeksiyon Perdesi Draper Clarion için çevrimiçi göz atın veya pdf Montaj/Montaj Talimatları indirin. Draper Clarion 4 sayfaları. Permanently tensioned projection screen
Ayrıca Draper Clarion için: Montaj/Montaj Talimatları (2 sayfalar), Montaj/Montaj Talimatları (4 sayfalar), Montaj/Montaj Talimatları (2 sayfalar), Montaj/Montaj Talimatları (3 sayfalar)
Sayfayı Yazdır
Clarion Permanently Tensioned Projection Screen by Draper
➀ Read instructions through completely before proceeding.
➁ Follow instructions carefully. Installation contrary to instructions
invalidates warranty.
➂ Screen should be accessible for complete removal should fabric
become damaged or should other service be required.
➃ Screen should be installed level (using a carpenter's level).
➄ Nothing should be fastened to screen frame or viewing surface.
➅ Operating switch(es), for electric tilting screens, packed separately in
screen carton. Do not discard with packing material.
➆ Electric tilting mechanism operates on 110-120v, 60 hz. current.
➇ Tools Required: Medium (#2) Phillips Screwdriver, Carpenters Level,
Soft face (rubber) Hammer & Measuring Tape.
NOTE: Screen has been thoroughly inspected and tested at factory and
found to be operating properly prior to shipment.
Assembly of "Knocked-Down" Screen
General—
Assemble inner frame on large table or on floor. Refer to the exploded
drawing on page 3 as you read these instructions.
Open cartons along the length, not at ends. Remove all pieces from the
carton. Lay out the four sections of the inner frame (top, bottom, left and right)
with the front sides facing up. (Back of frame is side with snaps.)
Screw the left and right sides to the top and bottom frame members using the
#6 x 1" screws through the two pre-drilled holes in each end of sides. Screws
should thread into the circular screw channels. Make sure frame assembly is
square by measuring across frame diagonals.
Place and screw one corner gusset to the inner frame assembly at each
corner with (6) #8 x
3
/
" pan head screws. Screws pass through pre-punched
8
holes in gussets and thread into screw channel on inner frame.
Connect horizontal brace and vertical brace using (2) #10 x
page 4 for the various configurations.
Copyright © 2002 Draper Inc.
Assembly/Mounting Instructions
Caution
#8 x 3/8"
Pan Head
Screw
Corner Gusset
1
/
" screws. See
2
Form Clarion_Inst02
Place bracing assembly inside the inner frame so the plates at each end of
braces are completely visible from the front. Make sure these braces are
perpendicular to the inner frame sections. Insert #8 x
holes in these plates and into the screw channel on the inner frame. The inner
frame assembly is now complete.
Slot Receives Screw
Attachment of Viewing Surface
Two people should attach the viewing surface of large screens, to
prevent possible damage.
Unroll the viewing surface from the core with the viewing side face down. Be
extremely careful to protect the viewing surface by unrolling it onto a clean
cloth or paper.
Place the inner frame assembly, with front side down , against the back of
the viewing surface. Make sure the top piece of frame corresponds with the
top side of the viewing surface.
Pull border snaps on viewing surface around the inner frame and snap to the
back side of the frame. Engage the 2 snaps at each corner first, then go along
each side and engage the remaining snaps.
Pivot the frame/fabric assembly up into a vertical position and inspect surface.
Lay frame/fabric assembly with viewing surface up. Frame is ready for
installation of trim frames.
Place the four trim sections next to the correct sides of the frame/fabric
assembly. The side trim sections will have connecting brackets located in
each end. These brackets will align and hold the face of the trim sections
together. Place the top and bottom trims over the top and bottom of the frame/
fabric assembly. (Do not slide the trim sections along the outside edges
of the frame/fabric assembly. Doing this could damage the fabric
viewing surface.)
Align and start engagement of bracket in the side trim with slot in top trim by
hand. Use rubber hammer to drive trims fully together. Repeat for the other
corners of screen.
Printed in U.S.A.
#10-24 x 1/2"
Flat Head
Screw
See detail for
configuration
possibilities
3
/
8
#8 x 3/8"
Pan Head
Audience
Screw
Side
Base
Frame
" screws through the