Draper Envoy Kurulum ve Kullanım Talimatları - Sayfa 2
Projeksiyon Perdesi Draper Envoy için çevrimiçi göz atın veya pdf Kurulum ve Kullanım Talimatları indirin. Draper Envoy 3 sayfaları. Electric projection screen
Ayrıca Draper Envoy için: Kurulum ve Kullanım Talimatları (3 sayfalar), Kurulum ve Kullanım Talimatları (3 sayfalar), Kurulum ve Kullanım Talimatları (2 sayfalar), Kurulum ve Kullanım Talimatları (2 sayfalar), Kurulum ve Kullanım Talimatları (2 sayfalar), Kurulum ve Kullanım Talimatları (3 sayfalar)
Sayfayı Yazdır
Envoy by Draper
13
7
/
"
16
9
7
/
"
16
1
4
/
"
1
16
/
"
8
9
7
/
"
16
Standard
Offset
Construction
Construction
Limit Adjustments (Built-in Low Voltage Motors)
Please Note: Screen limits are factory set for optimum performance
of the screen. A procedure is outlined below for minor tweaks, but
any adjustment of these limits may negatively affect the flatness of
the screen surface and could also void the warranty. Please check
with Draper prior to resetting screen limits.
CAUTION: Always be prepared to shut screen off manually when
new adjustment is being tested. Screen may be severely damaged if
viewing surface is allowed to run too far up or too far down.
1 Connect the ILT switch to the motor via the terminal blocks, or via the
modular port using four conductor modular cable. When using modu-
lar cable, the cable connectors MUST NOT be crimped in reverse, as
with standard telephone cable. (For a Dry Contacts Wiring Diagram,
see page 3.)
2 Set the slide switch to the lower position. Press and hold the DOWN
button on the switch to move the viewing surface to the desired lower
limit. If the screen moves in the opposite direction, release the DOWN
button and press and hold down the STOP button for four seconds.
This will reverse the operation of the UP and DOWN switches.
3 Move slider switch into center position. Wait a couple of seconds.
Please Note: If you move the slider switch from down to up in one
motion it sets the two limits in the same position.
4 Set the slide switch to the higher position. Move the viewing surface
to the desired upper limit by pressing and holding the UP button on
the wall switch.
5 Return the slide switch to the center position to return to normal
operation.
6 To set the viewing surface to an alternate format position, move the
viewing surface to the desired position and press the STOP button.
Press and hold the STOP button for at least three seconds to record
the position.
Please Note: Pressing and releasing the UP button on the switch will
move the screen to its upper limit. Pressing and releasing the DOWN
button will move the screen to its lower limit.
While the motor is in motion, pressing the STOP button for less than
two seconds will stop the viewing surface at its present position.
Once the motor is stopped, pressing the STOP button will move the
viewing surface to its alternate format position.
Pressing and holding the STOP button, when the motor is at rest or
in motion, for at least three seconds will record a new alternate format
position.
+
U
D
C
5V
p
o
o
DC
w
m
n
m
o
n
P
O
T
S
Slide
Switch
Back View
FUNCTION
POSITION
Case Dimensions/Method of Installation
Incl. mtg.
brackets
Support rods
by others
2¼"
5
Mounting
brackets
Surrounding
ceiling
1¼"
Conduit connection
2" up on this end
+
U
D
C
5V
p
o
o
DC
w
m
n
m
o
n
P
O
T
S
Please Note: 5V DC
To Motor
must be connected to
Slide
with
be able to set limits
Switch
Built-In
using the wall switch.
Low Voltage
Back View
FUNCTION
POSITION
Set LOWER limit
DOWN
Set UPPER limit
UP
Normal Operation
CENTER
To Motor
with
Built-In
Low Voltage
www.draperinc.com
2"
/
"
8
Viewing
7½"
surface
Please Note: Do not wire motors in parallel.
Single Station Control
Junction box at
left end of screen
Internal Screen Wiring
White (Common)
Red (Down)
Black (Up)
Green (Ground)
Dashed wiring
by installer
Single gang box by others
Control
Min. 4" x 2 1/8" x 1 7/8" deep
switch
Blue
Red
Black
Location of key
operated on-off
switch if furnished
To 110-120v Line
To Motor
Wiring Diagrams—110-120V Motor and Quiet Motor
with
Built-In
with Built-in Low Voltage Controller
Low Voltage
Single Low Voltage Control
Internal Screen Wiring
White (Neutral)
Black
Green/Yellow (Ground)
To Motor
Dashed wiring
Data Cable
with
by electrician
Built-In
Low Voltage
connector
Wall Switch,
RF or IR
Receiver,
or integrated
control system
To 110-120V Line
(765) 987-7999
Fabric Width + 15"
Ceiling
closure door
Wiring Diagrams
Multiple Station Control
Junction box at
left end of screen
Motor
Red
Black
Red
Black
Red
Black
Location of key
operated on-off
switch if furnished
To 110-120v Line
Multiple Low Voltage Controls
Dashed wiring
by electrician
RJ-9
To 110-120V Line
Page 2 of 3
2"
7
9
/
"
16
3¼"
Ceiling grid and
tile (by others)
Internal Screen Wiring
White (Common)
Red (Down)
Motor
Black (Up)
Green (Ground)
Cap off with wire
nut and tape
Blue
Dashed wiring
by installer
Blue
Blue
Single gang box by others
Min. 4" x 2 1/8" x 1 7/8" deep.
3 shown. More or less equally
feasible.
Internal Screen Wiring
White (Neutral)
Black
Green/Yellow (Ground)
Data
Cables
RJ-9
connectors
Wall Switches,
RF or IR
Receivers,
or integrated
control systems