Draper FlexShade Talimatlar Kurulum ve Çalıştırma - Sayfa 7

Projeksiyon Perdesi Draper FlexShade için çevrimiçi göz atın veya pdf Talimatlar Kurulum ve Çalıştırma indirin. Draper FlexShade 12 sayfaları. Exterior clutch-operated shade
Ayrıca Draper FlexShade için: Kurulum ve Kullanım Kılavuzu (8 sayfalar), Kurulum Talimatları (2 sayfalar), Talimatlar Kılavuzu (12 sayfalar), Kurulum ve Çalıştırma Talimatları (11 sayfalar), Talimatlar Kurulum ve Çalıştırma (12 sayfalar), Talimatlar Kurulum ve Çalıştırma (16 sayfalar), Talimatlar Kurulum ve Çalıştırma (4 sayfalar), Talimatlar Kılavuzu (7 sayfalar), Talimatlar Kurulum ve Çalıştırma (16 sayfalar)

Sayfayı Yazdır
Draper FlexShade Talimatlar Kurulum ve Çalıştırma
Exterior Clutch-Operated FlexShade

Section 4 - ENDCAP INSTALLATION: Mounting Endcaps

1.
Snap on
Endcap Covers.
(20# Clutch endcap shown.)
3.
Remove Bead
Chain Guard from
clutch endcap.
6.
Route Bead
Chain through
chain guide.
7.
Re-attach Bead Chain
Guard using provided
screw.
A. Mark wall, jamb, or
ceiling for placement
of mounting endcaps.
4.
Place spring-
loaded pin into
idler endcap.

Section 5 - Bead Chain Limits and Safety Device Installation

Attaching Stop Balls
Figure 7:
1. Set upper and lower travel limits by installing stop balls to
CHAIN LIMITS
bead chain
1. Attach
P-Clip Cord Tension Device
stop balls.
Please Note: Draper
do not comply with WMCA/ANSI Standard A100.1-2012 come
2. Crimp
with a P-Clip cord tension device pre-attached to bead chain
closed
with
(Fig. 8)
pliers.
that bead chain is held taut enough that children cannot pull it
away from wall or fit their head into loop.
Spring-Loaded Cord Tension Device
If Draper Clutch FlexShade complies with WMCA/ANSI Standard A100.1-2018, a Spring-Loaded Cord
Tension Device comes installed on bead chain
approved mechanical fasteners
(wood screws)
bead chain away from wall or fit their head into loop.
For more information, visit www.draperinc.com/WindowShades/WCMAcompliance.asp.
2. Pull tensioner down so that bead
chain is held taut and use mounting
hardware to keep it taut.
1. Install cord tension device to wall,
jamb, or sill.
Please Note: Bead chain should be taut
enough to move smoothly through device.
However, overtightening screws will
damage Spring-Loaded Tension Device.
®
2.
Mount endcaps
to wall.
B. Drill small starter
hole
(if necessary)
mounting surface.
5.
Slip notches on clutch into
clutch endcap.
Press to lock
in place.
(crimp closed using pliers) (Fig. 7)
Bead Chain Clutch-Operated shades that
®
. This device must be attached to wall, jamb, or sill so
. An approved permanent warning label and
(Fig. 9)
are included. Device is designed so that children cannot pull
(See safety note on page 2)
Sill
Mount
Figure 9:
CHAIN
TENSION
DEVICE
page 7 of 12
C. Mount endcaps using
in
hardware appropriate
for site conditions.
Figure 8:
P-CLIP
.
P-Clip
.
Jamb
Mount
Tensioner