Draper Luma 2 Kurulum ve Çalıştırma - Sayfa 3

Projeksiyon Perdesi Draper Luma 2 için çevrimiçi göz atın veya pdf Kurulum ve Çalıştırma indirin. Draper Luma 2 4 sayfaları. Heavy duty spring roller operated projection screen
Ayrıca Draper Luma 2 için: Teknik Özellikler (1 sayfalar), Broşür (16 sayfalar)

Sayfayı Yazdır

Luma 2

Section 3 - Hanging Screen and Methods of Installation

CAUTION: Product is very heavy: Installer must provide adequate attachment hardware

and anchors as required. Installer must also ensure that structure is of adequate strength.

CAUTION: Case must be mounted low enough from ceiling to gain access to bracket

screws.

General Information

When locating viewing surface and checking clearance for screen's operation, remember surface

is centered in case. Handle case carefully to protect its finish.

Regardless of mounting method, screen should be positively and securely supported so that

vibration or even abusive pulling on the viewing surface will not cause case to work loose or fall.

Installer must ensure that fasteners used are of adequate strength and suitable for the mounting

surface chosen.

WALL

Appropriate hardware

provided by installer.

Figure 1

6" Extension Bracket

Optional - must be speciﬁed

Wall Installation with Optional

(15.2cm)

Please Note: Optional - must be specified.

1. Mount brackets using hardware

recommended for "Wall Installation"

2. Suspend screen from front holes with "S"

hooks

For added safety, crimp both ends of "S" hooks so

screen cannot come off. For more rigid installation,

Figure 3

mount screen from back holes to front of bracket by

using screws and nuts provided with brackets.

Ceiling Opening Trim Kit

Optional - must be speciﬁed

Screen

Case

Back

Ceiling Tile

(By others)

SUSPENDED

Appropriate hardware

provided by installer.

If using "S" Hooks,

Figure 2

installer must crimp

both ends of hooks

to safely secure the

screen.

Ceiling Opening Trim Kit

Optional - must be speciﬁed

Extension Brackets

(Fig. 3)

Screen

Case

(above)

(as in "Suspended Installation," above)

Trim Kit

(203 mm)

2 "

(54 mm)

electrical connection

Mounting angle and

hardware by others.

Suggested for

recessed installations.

* If using "S" Hooks (by others),

installer must crimp both

ends of hooks to safely

secure the screen.

Wall Installation

Mount screen through holes in back of endcaps as shown. Installer should

furnish screws, toggle bolts, molly bolts, nylon, or lead anchors as required.

Suspended Installation

Suspend screens from holes in endcaps as shown. "S" hooks, chains

, and turnbuckles should be provided by installer. "S" hooks should

cable)

go through the front holes on the endcaps, and both ends of "S" hooks

should be crimped for additional safety.

Chains should be attached to beams or other structural members.

Turnbuckles should be adjusted so screen hangs level.

Wall or Ceiling Installation with Optional Floating Brackets

Please Note: Optional - must be specified.

Floating brackets should be located on studs or joists. Bracket then

attaches at almost any point along case. For details, see separate

Trim Kit

instruction sheet that ships with Floating Wall Bracket.

Back

Ceiling Tile

Figure 4

(By others)

Recessed Installation

Please Note: Ceiling Opening Trim Kit is optional - must be specified.

Recess should permit access for removal of screen if necessary.

Screen may be mounted as in suspended or wall installation.

(See separate instruction sheet included with Ceiling Opening Trim Kit)

Please Note: Ceiling Opening Trim Kit is for use in an acoustical,

drop ceiling only. Not recommended for drywall or hard ceilings.

2 "

(52 mm)

1 "

(27 mm)

(102 mm)

6 "

Figure 5

(171 mm)

Fasteners for wall mounting

by others. ( "

hole)

(6mm)

hole for

(22mm)

(Fig. 1)

(Fig. 2)

(Fig. 5)

page 3 of 4

S Hooks for

suspended

installation

by others.*

( "

hole)

(6mm)

(or

(Fig. 4)