Draper Rolleramic Electric Projection Screen Kurulum ve Kullanım Talimatları - Sayfa 2
Projeksiyon Perdesi Draper Rolleramic Electric Projection Screen için çevrimiçi göz atın veya pdf Kurulum ve Kullanım Talimatları indirin. Draper Rolleramic Electric Projection Screen 2 sayfaları. Draper rolleramic electric projection screen installation/operating instructions
Sayfayı Yazdır
Rolleramic by Draper
Rolleramic Mounting Bracket
For suspended mount.
3
6
/
"
8
3
1
/
"
8
For wall mount
Please Note: Mount the case using the two end brackets fi rst. If
a center bracket is provided, mount it last. The center bracket is
designed to prevent sagging of the case, and must be mounted
so that it is level with the others and does not force the screen
case up. Make sure the top of the screen case's bottom board at
no point touches the roller/viewing surface.
Single Station Control
Junction box at
left end of screen
Internal Screen Wiring
White (Common)
Red (Down)
Black, or Blue (Up)
Green (Ground)
Dashed wiring
by electrician
Single gang box by others
Control
Min. 4" x 2 1/8" x 1 7/8" deep
switch
Blue
Red
Black
Location of key
operated on-off
switch if furnished
To 110-120V Line
Rolleramics over 12' x 12'
have a blue wire lead
instead of a black wire lead
coming from the motor.
Case Dimensions
11
Rolleramic Wiring Diagrams
Multiple Station Control
Junction box at
left end of screen
Red
Black
Red
Black
Red
Black
Location of key
operated on-off
switch if furnished
To 110-120V Line
Low Voltage & Wireless Control
White-Common to screen & 110-120V AC Neutral
Red-to screen (directional)
Brown-to screen (directional)
Yellow-to 110-120V AC-Hot
Black-to 110-120V AC-Hot
Green-Ground
Dashed wiring by electrician
Low voltage wiring by others
Eye Port for IR Eye, RF Receiver or LED
Wall Switch. For more than one of
these, a splitter is required.
3 Button Wall Switch
DOWN - Red
COM - White
UP - Black
Aux Port for connecting additional LVC-III
modules (up to six total can be linked-
connect from Aux to Eye).
www.draperinc.com
Conduit
connection
1
/
"
5
1
2
9
/
"
9
/
"
8
8
5
9
/
"
8
1
9
/
"
8
Case
¾" thick
Through 12' x 12' 14¾"
Over 12' x 12' 21¼"
Access
Bottom
Door
Internal Screen Wiring
White (Common)
Red (Down)
Black, or Blue (Up)
Green (Ground)
Cap off with wire
nut and tape
Blue
Dashed wiring
by electrician
Blue
Blue
Single gang box by others
Min. 4" x 2 1/8" x 1 7/8" deep.
3 shown. More or less equally
feasible.
Internal Screen Wiring
White (Common)
Red (Down)
Black (Up)
Green (Ground)
STOP
Location of key
operated on-off
switch if furnished
STOP
Control
Switches
24v DC
(765) 987-7999
L = W+24" (through 12' x 12')
L = W+30" (over 12' x 12')
Screen
surface
Fabric width – W
Bottom board
Two-Way Serial Communication
(RS232) with MC1
See separate Serial Communication-
RS232 Instruction sheet for enabling
RS232 with the MC1.
To
110-120V
Line
Page 2 of 2
Front
5
4
/
"
8
1
4" - 4
/
"
8
Opening for fabric