Draper Targa Kurulum ve Kullanım Talimatları - Sayfa 2

Projeksiyon Perdesi Draper Targa için çevrimiçi göz atın veya pdf Kurulum ve Kullanım Talimatları indirin. Draper Targa 2 sayfaları. Electrically operated projection screen with motor-in-roller
Ayrıca Draper Targa için: Kurulum ve Kullanım Talimatları (4 sayfalar), Kurulum ve Kullanım Talimatları (2 sayfalar), Kurulum ve Kullanım Talimatları (2 sayfalar), Kurulum ve Kullanım Talimatları (4 sayfalar), Kurulum ve Kullanım Talimatları (2 sayfalar), Kurulum ve Kullanım Talimatları (3 sayfalar), Kurulum ve Kullanım Talimatları (4 sayfalar), Kurulum ve Kullanım Talimatları (2 sayfalar), Kurulum ve Kullanım Talimatları (2 sayfalar), Talimatlar Kılavuzu (8 sayfalar)

Sayfayı Yazdır
Draper Targa Kurulum ve Kullanım Talimatları
220V Targa and Premier —Large Sizes by Draper
Types of Installation
Ceiling Mounted
Wall Mounted
Appropriate hardware
provided by installer.
Product is very heavy: Installer must provide adequate
attachment hardware and anchors as required. Installer
must also insure that wall or ceiling structure is of
adequate strength.
Tab-Tension Adjustment
Procedure for Premier
➀ Determine which side requires adjustment.
➁ Secure dowel with one hand.
Caution: Do not touch or bend surface.
➂ Using Philips-head screwdriver,
depress spring-loaded
adjustment screw (see drawing)
and slowly turn clockwise
Dowel
to tighten tension, or
counterclockwise to loosen
tension. The screw adjusts
in ¼ turn increments.
Adjust only one increment (¼ turn).
➃ If problem is not corrected, leave screen in position
for 24 hours to allow surface material to stretch into position.
➄ If problem still is not corrected, repeat steps 2 and 3.
Two-Way Serial Communication
(RS232) with MC1
Case Dimensions
Case Dimensions (Premier Tab Tension Surface Shown)
16.8
cm
16.8
cm
Appropriate
8.6
cm
hardware
provided
8.6
by installer.
R73
cm
cm
63 mm
Dim Targa
A 22.54 cm Varies
B 7.62 cm Varies
Single Station Control
CE Approved
Tensioning
Cable
Adjustment
Screw
Dashed wiring
by electrician
See separate Serial Communication-
RS232 Instruction sheet for enabling
RS232 with the MC1.
www.draperinc.com
1
cm
1.7
cm
B
Premier
Wiring Diagrams
Terminal strip in
junction box at left
end of screen
Control
switch
230V,
PE
50 Hz.
Low Voltage & Wireless Control
Red-to screen (directional)
Brown-to screen (directional)
White-Common to screen, 230V AC
Black-to 230V AC
Yellow-to 230V AC
Green-Ground
Dashed wiring by electrician
Low voltage wiring by others
Eye Port for IR Eye, RF Receiver or LED
Switch For more than one of these,
a splitter is required.
3 Button Wall Switch
DOWN - Black
COM - White
UP - Red
Aux Port for connecting additional
LVC-III modules (up to six total-
connect from Aux to Eye).
(765) 987-7999
Page 2 of 2
Surface Width + A
Multiple Station Control
Not CE Approved
Terminal strip in
junction box at left
end of screen
Red
Black
Red
Black
Red
Black
Dashed wiring
by electrician
230V, 50 Hz.
All-Pole Disconnect
by Others
STOP
STOP
230V, 50 Hz.
Control
Switches
24v DC
10
cm
Cap off with wire
nut & tape
Blue
Blue
Blue
Terminal strip in
junction box at left
end of screen