Targa by Draper
"DOWN" LIMIT ADJUSTMENT
To Reduce Screen Drop
➀ Raise screen surface about 1' above desired setting and turn off.
➁ Turn the DOWN limit screw (I) clockwise (three screw turns = ½ roller
revolution).
➂ Test by running screen down and repeat steps 1 and 2 until desired position
is reached.
To Increase Screen Drop
➀ Run screen to the down limit.
➁ With the down switch on, turn the DOWN limit screw (I) counterclockwise
(three turns of screw equals ½ roller revolution) to increase drop.
➂ Test by running screen up about 1' and back down to new down limit.
➃ Repeat steps 2 and 3 until desired position is reached.
CAUTION: At least 1¼ wraps of fabric must remain on the roller when
screen is at the down limit!
"UP" LIMIT ADJUSTMENT
Screen is Running Too Far Up
➀ Lower screen surface about 1' below desired setting and turn off.
➁ Turn the UP limit screw (II) clockwise (three screw turns = ½ roller
revolution).
➂ Test by running screen up.
➃ Repeat steps 1 through 3 until desired position is reached.
Screen Needs to Run Up More
➀ Run screen down about 1' and turn off.
➁ With the up switch on, turn the UP limit screw (II) counterclockwise (three
turns of screw equals ½ roller revolution).
➂ Repeat steps 1 and 2 until desired position is reached.
CAUTION: Do NOT allow the dowel to wrap up over the roller when the
screen is running up! This could damage the screen.
Limit Adjustments (Built-in Low Voltage Motors)
(Height adjustments are made from wall switch)
➀ Connect the ILT switch to the motor via the terminal blocks, or via the
modular port using four conductor modular cable. When using modular
cable, the cable connectors MUST NOT be crimped in reverse, as with
standard telephone cable.
➁ Set the slide switch to the lower position.
Press and hold the DOWN button on the
switch to move the viewing surface to the
desired lower limit. If the
POSITION
screen moves in the op-
posite direction, release
the DOWN button and
press and hold down the
STOP button for four seconds. This will
reverse the operation of the UP and
DOWN switches.
③ Move slider switch into center position.Wait a couple of seconds.
Please Note: If you move the slider switch from down to up in one mo-
tion it sets the two limits in the same postion.
➃ Set the slide switch to the higher position. Move the viewing surface to the
desired upper limit by pressing and holding the UP button on the wall
switch.
➄ Return the slide switch to the center position to return to normal operation.
➅ To set the viewing surface to an alternate format position, move the viewing
surface to the desired position and press the STOP button. Press and
hold STOP for at least three seconds to record the position.
Please Note: Pressing and releasing the UP button on the switch will move
the screen to its upper limit. Pressing and releasing the DOWN button will
move the screen to its lower limit.
While the motor is in motion, pressing STOP for less than two seconds will
stop the viewing surface at its present position.
Once the motor is stopped, pressing the STOP button will move the viewing
surface to its alternate format position.
Pressing and holding the STOP button, when the motor is at rest or in mo-
tion, for at least three seconds will record a new alternate format position.
P
O
T
S
U
D
C
p
o
o
w
m
n
m
o
n
FUNCTION
P
O
T
S
P
O
T
S
DOWN
Set LOWER limit
Set UPPER limit
UP
Normal Operation
CENTER
Slide
Switch
Back View
www.draperinc.com
5¼"
5
2
/
"
16
7
5
/
"
8
7
/
" dia.
8
electrical
connection
hole
To Motor
with
Built-In
+
5V
Low Voltage
DC
To Motor
with
Built-In
Low Voltage
Wall Mounted
Appropriate hardware
provided by installer.
(765) 987-7999
Case Dimensions
Fabric width + 7"
3½"
Methods of Installation
Fasteners for
wall mounting
by others.
7
/
" hole for
8
electrical
connection.
Optional Ceiling Opening Trim Kit
(Dims-Side View)
8"
1
1
2
/
"
8
4"
3
6
/
"
4
Types of Installation
Suspended
Appropriate hardware
provided by installer.
Page 2 of 3
Viewing
Surface
S Hooks for
suspended
installation
by others.
1
2
/
"
16
1
/
"
16
6" Extension
Bracket
Sayfayı Yazdır