Bosch WAE24272AU Kullanım Kılavuzu - Sayfa 8
Yıkayıcı Bosch WAE24272AU için çevrimiçi göz atın veya pdf Kullanım Kılavuzu indirin. Bosch WAE24272AU 8 sayfaları. Washing machine
Sayfayı Yazdır
What to do if ...
Water is leaking out.
– Attach/replace the drainage hose correctly.
– Tighten the screw connection of the supply hose.
No water supply.
– Is
– Tap not turned on?
Detergent not dispensed.
– Filter blocked? Clean the filter –> page 10.
– Supply hose kinked or trapped?
Washing machine door
– Safety function active. Wait approx. 2 minutes.
cannot be opened.
– - - - - (without final spin) selected? –> page 4.
Programme does not
–
Start/Pause or
start.
– Washing machine door closed?
Detergent solution is not
– - - - - (without final spin) selected? –> page 4.
drained.
– Clean the detergent solution pump –> page 10.
– Clean the waste pipe and/or drainage hose.
Water not visible in the
– Not a fault - water below the visible area.
drum.
Unsatisfactory spin
– Not a fault - the unbalanced-load detection system has cancelled
result.
the spin cycle because of uneven distribution of the laundry.
Laundry wet/too damp.
Distribute small and large items of laundry evenly inside the drum.
– Speed selected too low? –> page 5.
The programme duration
– Not a fault – the programme sequence is optimised for the
changes during the wash
particular wash process. This may result in changes to the
cycle.
programme duration in the display field.
Spin cycle performed
– Not a fault - unbalanced load detection system adjusts the
several times.
imbalance.
Residual water in the
– Not a fault - the action of the care product is not affected.
compartment for care
– Clean the insert if necessary –> page 9.
products.
Odour formation in the
– Run programme
washing machine.
standard detergent.
Foam may be coming
– Too much detergent used? Mix 1 tablespoon of fabric softener
out of the detergent
with ½ litre of water and pour into dispenser II (not for outdoor
and down-filled textiles!).
drawer.
– Reduce the detergent dosage for the next wash cycle.
Intense noise formation,
– Are the appliance feet fixed?
vibrations and
Secure the appliance feet –> Installation instructions.
"wandering" during the
– Transportation safety devices removed?
spin cycle.
Remove the transportation safety devices –> Installation
instructions.
Noises during spin and
– Clean detergent-solution pump –> page 10.
drain cycles.
Display panel/indicator
– Power cut?
lamps do not function
– Fuses triggered? Reset/change the fuses.
during operation.
– If the fault occurs repeatedly, call the after-sales service.
Programme sequence
– Not a fault - unbalanced load detection system adjusts
longer than usual.
imbalance by repeatedly distributing the laundry.
– Not a fault - foam detection system active - adds an additional
rinse cycle.
Detergent residues on
– Occasionally, phosphate-free detergents contain water-insoluble
the laundry.
residues.
– Select
If you cannot correct a fault yourself (switching on/off) or a repair is required:
– Turn the programme selector to Off and remove the mains plug from the socket.
– Turn off the water supply and call the after-sales service –> Installation instructions.
Start/Pause not selected?
Start in selected?
Cottons Stains 90 °C without laundry. Use
Rinse/Freshen up or brush the laundry after washing.
Observe the safety instructions on page 8.
Read these instructions and the separate installation instructions
before operating the washing machine.
11
Washing machine
Instruction manual
en