Draper Battery Powered FlexShade Kurulum Talimatları - Sayfa 2
İç Mekan Mobilyaları Draper Battery Powered FlexShade için çevrimiçi göz atın veya pdf Kurulum Talimatları indirin. Draper Battery Powered FlexShade 3 sayfaları.
Sayfayı Yazdır
Battery Powered FlexShades by Draper
Surface Mount Headbox
1 Snap endcap covers onto endcaps.
2 Place endcaps into back/top portion of headbox. Using pre-drilled holes in
endcaps, mark the back/top portion of headbox for drilling.
3 Drill holes in back or top, depending on whether you will be mounting the
headbox to the wall or ceiling.
4 Attach headboxback/top and endcaps to wall or ceiling using mounting
hardware appropriate for installation site conditions.
5 Mount battery wands somewhere outside the headbox (see "Battery
Mounting" section above).
6 Install shade (see "Shade Installation" section above).
7 Place face cover on headbox (see Fig. 6).
3
7
/
"
8
or
5
4
/
"
8
"
1
/
4
RF Remote Programming Instructions
Please Note: The motor has no programming on it so it
must be learned and programmed to work on the transmit-
ter that you have at the job. Here are the initial program-
ming instructions.
1 Connect the battery wand to one motor. Select the transmitter/channel to
which you plan to learn the motor. Press and hold the UP and DOWN but-
tons at the same time until the motor jogs, then release.
2 Check the motor run direction by pressing either the UP or DOWN buttons.
This is important because if you do step 3 without doing this step, then
you will need to reset the motor. If you need to reverse the motor direction,
then press the STOP button (middle button which might be labeled MY) for
five seconds until the motor jogs. Check the direction again to make sure
that it works.
3 Move the motor to its upper limit position. Press the STOP and DOWN
buttons at the same time until the motor starts to move down, then release.
You will stop the motor at its lower limit. You can use the UP and DOWN
buttons to adjust the motor to the correct lower limit position if need be.
4 Once the motor is at its lower limit position, then press the UP and STOP
buttons at the same time until the motor starts to move up, then release.
The motor should move to the upper limit position in step 3 and stop.
5 Once the motor has stopped at its upper limit position, then press and hold
the STOP button for five seconds until the motor jogs.
6 Now, you must put the motor into USER mode. Find the programming
button which is a small button on the back or side of the transmitter and
press it until the motor jogs. Once you have done this, then the motor will
operate in normal fashion.
3
3
/
"
8
or
4
5
/
"
8
Figure 6
www.draperinc.com
7 Disconnect power to this motor and move to the next in your installation
and start with step 1. Reconnect motor to power when all motors are
programmed.
Reset Motor Instructions
If the motor is not working or responding correctly and you want to reprogram
it from the beginning and clear all previous programming, then follow this.
1 Using a paperclip, press and hold the program button on the motor head
until the motor jogs 3 times. This erases all transmitters and limits.
Setting an Intermediate Stop
This is done once the shade is in USER mode from the initial programming at top.
1 Move the motor to the mid-point location that you want the stop located.
2 Press and hold the STOP button until the motor jogs.
3 Now, if you hit the STOP button when the motor is standing still, it will move
to that intermediate location.
4 If you want to delete the stop, then go to the intermediate stop and press
and hold the STOP button until the motor jogs.
Add/Delete a Channel/Transmitter
To add a channel/transmitter:
1 Select the channel/transmitter that is currently operating the motor, then
press the programming button until the motor jogs.
2 Select the new channel/transmitter that you want to add to the motor, then
press the programming button until the motor jogs.
3 The motor should now work on both the old and new channel/transmitter.
Channel se-
lector button
on Multi-
Channel
Transmitter
To delete a channel/transmitter:
1 Select the channel/transmitter that is currently operating the motor and
you want to keep, then press and hold the programming button until the
motor jogs.
2 Select the channel/transmitter that you want to remove, then press and
hold the programming button until the motor jogs.
3 The motor should now only work on the channel/transmitter on step 1.
Adjust Limits in User Mode
If your initial limits have changed or you want to fine tune a motor, you do
not need to reset the motor and re-program it. You can just change the limits
with these steps.
1 Move the motor to the limit (upper or lower) that you want to change.
2 Press and hold the UP and DOWN buttons until the motor jogs.
3 Move the motor to its new limit location.
4 Press and hold the STOP button until the shade jogs.
Please Note: For instructions with Programmable Timer,
please consult instructions provided with the timer.
Cleaning and Maintenance
Idlers on motorized shades may occasionally need lubrication. If lubrica-
tion is required, apply a small amount of a lithium based grease direct to the
idler pin.
Most of Draper's standard fabrics may be cleaned at the window by
vacuuming with a soft brush attachment. They may also be cleaned by using a
sponge or soft cloth and mild solution of warm soapy water. A dishwashing liq-
uid, such as Ivory liquid, is recommended. A clean dry cloth is recommended
for the metal finish.
(765) 987-7999
Page 2 of 3