Draper Exterior FlexShade Clutch Kurulum ve Çalıştırma Talimatları - Sayfa 5
İç Mekan Mobilyaları Draper Exterior FlexShade Clutch için çevrimiçi göz atın veya pdf Kurulum ve Çalıştırma Talimatları indirin. Draper Exterior FlexShade Clutch 8 sayfaları.
Sayfayı Yazdır
Exterior FlexShade
Exterior window shade with smooth, quiet operation, and independent control
Section 3 - Endcaps with Fascia—Free-Hanging
Caution: Before mounting shades, verify measurements on card provided with shade, and ensure unit is installed at correct width.
Please Note: Installer is responsible for selecting mounting hardware appropriate for site conditions.
1. Mark wall, jamb or ceiling for placement of mounting endcaps.
2. Drill small starter hole
(if necessary)
3. Snap endcap
covers(Fig. 4)
into place.
4. Mount endcaps using appropriate fasteners for surface
5. Place spring-loaded pin into idler endcap, depress pin by pushing shade roller toward endcap, slip notches on operator end
into other endcap, then press down to lock in place
6. Properly route bead chain through chain guide, then attach chain guide cover to chain guide using provided screw
Caution: Be sure to lock chain guide cover to chain guide with provided screw.
Figure 5 - Endcap Installation
SMALL
Idler
Idler End
Endcap
of Roller
Retainer Clip
LARGE
Idler
Idler End
Endcap
of Roller
Retainer Clip
Section 4 - Bead Chain Limits and Saftey Device Installation
Section 4.1 - Attaching Stop Balls
1. Set upper and lower travel limits by installing stop balls to bead chain
Section 4.2 - P-Clip Cord Tension Device
Please Note: Draper Bead Chain Clutch Operated shades that do not comply with WMCA/ANSI Standard
A100.1-2012 come with a cord tension device pre- attached to bead chain
attached to wall, jamb or sill so that bead chain is held taut enough that children cannot pull it away from
wall or fit their head into loop.
Section 4.3 - Spring-Loaded Cord Tension Device
Draper Clutch FlexShade complies with WMCA/ANSI Standard A100.1-2012, a Spring-Loaded Cord Tension
Device comes installed on bead chain
(wood screws)
mechanical fasteners
away from wall or fit their head into loop.
For more information, visit
www.draperinc.com/WindowShades/WCMAcompliance.asp.
Please Note: Overtightening screws will damage Spring Loaded Tension Device.
Caution: Do not allow shade roller to become exposed by running shade fabric too far down. Be sure to
use stop balls provided in hardware packet by Draper to set up and down travel limits. Stop balls by
others may be too small, and become lodged in clutch mechanism.
Please Note: If shade fabric is uneven, see "Field Adjustments" section
- Clutch
®
in mounting surface.
(Fig.
5).
(Fig.
5).
10 lb Clutch
24 lb Clutch
45°
(Fig.
9). An approved permanent warning label and approved
are included. Device is designed so that children cannot pull bead chain
(See safety note on page
2).
Clutch
Endcap
Clutch
Endcap
(crimp closed using pliers) (Fig.
7).
(Fig.
8). This device must be
(pg.
2).
page 5 of 8
Figure 4
(Fig.
6).
Figure 6
OR
Figure 7
Figure 8
Attach Stop
Balls
Crimp
Closed
with
Pliers
Figure 9
Sill
Mount
Tensioner
Jamb
Mount