Dual Roller Coupled Motorized FlexShade
Section 7 - Limit Switch Adjustments
Section 7.1 - Standard and Quiet Motors
Section 7.1.1- Push Button Limits
1. Fully depress both limit switch push buttons, then
operate wall switch to make sure system works properly.
2. Raise shade to desired "up" stop position.
3. Set upper limit by depressing proper
4. Lower shade to desired "down" stop position.
5. Set lower limit by depressing proper
Section 7.1.2 - Screw-Type Limits
1. Determine which direction of fabric travel corresponds
with arrows on motor.
2. Operate shade to desired "down" stop position.
Set limit by turning proper socket toward "+" to lower limit, and "-" to raise it.
3. Operate shade to desired "up" stopping position. Set limit by turning proper screw
toward "-" to raise limit, and "+" to lower it.
Section 7.2 - Limit Adjustments: RS485 Motors
For limit setting instructions on these motors, see instructions packaged with the RS485 Address/Limit Setting Tool
Section 7.3 - Limit Switch Adjustments: RTS Motors
For limit setting instructions on these motors, see Radio Frequency Remote Control Programming Instructions
Section 7.4 - Limit Switch Adjustments: IntelliFlex I/O Motors
For limit setting instructions on these motors, see instructions packaged with the Motor Limit Setting Tool
Section 8 - Electrical Connections
Shade operates on 110-120V, 60 Hz. current. Shade is shipped with internal wiring complete and control switch
cable lead. Longer lead can be substituted by removing two screws in motor end of roller, removing lead, plugging new lead in, and replacing screws. Wire to connect
shade to switch
and switch
to power supply should be furnished by installer.
(es)
(es)
Connections should be made in accordance with attached wiring diagram, and wiring should comply with national and local electrical codes. DO NOT wire motors in
parallel without written permission from Draper.
All operating switches should be "off" before power is connected.
Please Note: For low-voltage wiring requirements, Draper recommends consulting with a professional low-voltage electrical contractor. It is very important that
shielded and stranded CAT 5 cable be used to prevent any electrical interference.
Please Note: A Draper Motor Test Cable
IMPORTANT: To reduce the risk of electric shock, equipment that features a grounding type attachment plug has a third
This plug will ONLY fit into a grounding type outlet. If the plug does not fit into the outlet, a qualified electrician must install the proper outlet.
Do not change the plug in any way.
Do not use an extension cord. If the power supply cord is too short, a qualified electrician must install an outlet near the motor.
(All procedures shown are for Standard Roll. Invert orientation for Reverse Roll)
Caution:
- Be sure all switches are in "off"
position before adjusting limit
switches.
- Be prepared to shut off
push button.
(back)
manually while testing.
- Shade may be damaged by
running shade fabric down too
push button.
(front)
far to expose roller.
- If using a group control system,
each limit switch must be set
prior to connecting to system.
- Motor must be installed so limit
switches are pointed down.
and M12 Pigtail
(Part# 503109)
(Part# C107.089.60)
®
(Extra Large Hardware)
PUSH BUTTON LIMITS
ROOM SIDE
Front
Back
GLASS SIDE
SCREW-TYPE LIMITS
ROOM SIDE
Front
Back
GLASS SIDE
Figure 15
(part# C156.241)
Screws
(FS_MO_RFRC_ProgInst)
.
(part# C202.030)
fully boxed, and standardly supplied with a 6'
(es)
are available for temporary power for testing and limit setting.
ROOM SIDE
page 9 of 12
Front
Back
Standard right-hand
GLASS SIDE
Bottom View
motor configuration shown
ROOM SIDE
+
Front
Back
+
Side View
Bottom View
GLASS SIDE
Standard right-hand
Bottom View
motor configuration shown
+
Side View
+
Screws
Side View
Bottom View
.
Side View
.
pin on the attachment plug.
(grounding)
(1.8 m)
Sayfayı Yazdır