Draper 65084 Kullanıcı Kılavuzu - Sayfa 6

Sander Draper 65084 için çevrimiçi göz atın veya pdf Kullanıcı Kılavuzu indirin. Draper 65084 16 sayfaları. Dual action air composite sander
Ayrıca Draper 65084 için: Orijinal Talimat Kılavuzu (20 sayfalar)

Sayfayı Yazdır

HEALTH AND SAFETY INFORMATION

5.1

GENERAL SAFETY INSTRUCTIONS FOR POWER TOOL USE

When using any type of power tool there are steps that should be taken to make sure that you, as

the user, remain safe.

Common sense and a respect for the tool will help reduce the risk of injury.

Read the instruction manual fully. Do not attempt any operation until you have read and

understood this manual.

Most important you must know how to safely start and stop this machine, especially in an

emergency.

Keep the work area tidy and clean. Attempting to clear clutter from around the machine during

use will reduce your concentration. Mess on the floor creates a trip hazard. Any liquid spilt on the

floor could result in you slipping.

Find a suitable location. If the machine is bench mounted, the location should provide good

natural light or artificial lighting as a replacement. Avoid damp and dust locations as it will have a

negative effect on the machine's performance. If the machine is portable do not expose the tool to

rain. In all cases do not operate power tools near any flammable materials.

Keep bystanders away. Children, onlookers and passers by must be restricted from entering the

work area for their own protection. The barrier must extend a suitable distance from the tool user.

Unplug and house all power tools that are not in use. A power tool should never be left unattended

while connected to the power supply. They must be housed in a suitable location, away locked up

and from children. This includes battery chargers.

Do not overload or misuse the tool. All tools are designed for a purpose and are limited to what

they are capable of doing. Do not attempt to use a power tool (or adapt it in any way) for an

application it is not designed for. Select a tool appropriate for the size of the job. Overloading a tool

will result in tool failure and user injury. This covers the use of accessories.

Dress properly. Loose clothing, long hair and jewellery are all dangerous because they can

become entangled in moving machinery. This can also result in parts of body being pulled into the

machine. Clothing should be close fitted, with any long hair tired back and jewellery and neck ties

removed. Footwear must be fully enclosed and have a non-slip sole.

Wear personal protective equipment (PPE). Dust, noise, vibration and swarf can all be

dangerous if not suitably protected against. If the work involving the power tool creates dust or

fumes wear a dust mask. Vibration to the hand, caused by operating some tools for longer periods

must be protected against. Wear vibration reducing gloves and allow long breaks between uses.

Protect against dust and swarf by wearing approved safety goggles or a face shield. These are

some of the more common hazards and preventions, however, always find out what hazards are

associated with the machine/work process and wear the most suitable protective equipment

available.

Do not breathe contaminated air. If the work creates dust or fumes connect the machine (if

possible) to an extraction system either locally or remotely. Working outdoors can also help if

possible.

Move the machine as instructed. If the machine is hand held, do not carry it by the power supply

cable. If the product is heavy, employ a second or third person to help move it safely or use a

mechanical device. Always refer to the instructions for the correct method.

Do not overreach. Extending your body too far can result in a loss of balance and you falling. This

could be from a height or onto a machine and will result in injury.

Maintain your tools correctly. A well maintained tool will do the job safely. Replace any damaged

or missing parts immediately with original parts from the manufacturer. As applicable, keep blades

sharp, moving parts clean, oiled or greased, handles clean, and emergency devices working.

Wait for the machine to stop. Unless the machine is fitted with a safety brake, some parts may

continue to move due to momentum. Wait for all parts to stop, then unplug it from the power supply

– 6 –