Bosch 800 Series Kullanım ve Bakım Kılavuzu - Sayfa 7

Fırın Bosch 800 Series için çevrimiçi göz atın veya pdf Kullanım ve Bakım Kılavuzu indirin. Bosch 800 Series 12 sayfaları. Built-in wall ovens
Ayrıca Bosch 800 Series için: Kurulum Talimatları Kılavuzu (24 sayfalar), Kurulum Kılavuzu (40 sayfalar), Kurulum Kılavuzu (23 sayfalar), Kurulum Kılavuzu (28 sayfalar), Kurulum Kılavuzu (32 sayfalar), Kullanım Kılavuzu (32 sayfalar), Kurulum Kılavuzu (32 sayfalar), Hızlı Başlangıç ve Güvenlik Kılavuzu (7 sayfalar), Kullanım ve Bakım Kılavuzu (40 sayfalar), Kurulum Kılavuzu (40 sayfalar), Kurulum Kılavuzu (32 sayfalar), Kurulum Talimatları Kılavuzu (40 sayfalar), Kurulum Kılavuzu (48 sayfalar), Kullanım ve Bakım Kılavuzu (33 sayfalar), Kullanım ve Bakım Kılavuzu (49 sayfalar), Hızlı Başlangıç Kılavuzu (7 sayfalar), Hızlı Başlangıç ve Güvenlik Kılavuzu (13 sayfalar), Kurulum Kılavuzu (32 sayfalar), Servis Kılavuzu (36 sayfalar), Kurulum Talimatları Kılavuzu (29 sayfalar), Kullanım ve Bakım Kılavuzu (24 sayfalar), Kullanım ve Bakım Kılavuzu (40 sayfalar), Kurulum Talimatları Kılavuzu (28 sayfalar)

Sayfayı Yazdır
Bosch 800 Series Kullanım ve Bakım Kılavuzu

Operating the appliance

These instructions apply to several appliance models. It
is possible that individual features are described that do
not apply to your appliance.
Note: Turn the hood on a few minutes before you start
cooking and switch it off a few minutes after you have
finished cooking. This is the most effective way to
eliminate cooking vapor.
Control panel
Explanation
1
Turn the fan down
2
Turn the fan up
3
Display panel
4
Switch on lighting
5

Timer

Turn on the fan
Note: Always adjust the fan strength to meet current
conditions. If there is a large build-up of steam or fumes,
select a high fan setting.
Switching on
Press "+" button.
The current fan settings are indicated by a bar
on the display panel.
Press "+" or "-" keys to change the fan settings.
Switching off
Press the "-" button repeatedly until the fan
switches off.

Lighting

The lighting can be switched on and off independently of
the ventilation.
1.
Press the "Light" button.
The lighting switches on.
2.
Press the "Light" button again.
The brightness increases.
Press the "Light" button a third time.
3.
The lighting switches off.

Saturation notification

The saturation of the metal grease filter (after 30 hours of
ventilation operation) or of the activated carbon filter
(after 120 hours of ventilation operation) is indicated on
the display panel:
Metal grease filter: "clean grease filter" appears on
the display panel.
Activated carbon filter: "replace charcoal filter"
appears on the display panel.
If you have not yet done so, the metal mesh grease filters
should be cleaned or the activated carbon filter changed
now.
For instructions on how to clean the metal grease filters,
please refer to the Cleaning and maintenance section.
Resetting the saturation displays
Metal grease filter: Press and hold the "+" button for 5
seconds.
Activated carbon filter: Press and hold the "-" button
for 5 seconds.
Switching over the display for circulating-air mode
For circulating-air mode, the electronic control display
must be switched over accordingly:
The hood must be connected and switched off.
Press the "+" and "-" keys simultaneously until "Able"
lights up briefly on the display panel.
Repeatedly press the button combination to switch the
electronic control display back to exhaust air mode.
"None" appears on the display panel.
Timer
The timer has no influence on the functions of the
exhaust hood. The duration of the timer can be set to
between 1 minute and 60 minutes. The default setting is
10 minutes.
Press the "Timer" button.
1.
10 flashes on the display panel.
2.
Set the required duration with the "+" and "-" buttons.
After 5 seconds, the time that has been set is adopted.
An audible signal sounds once the time has elapsed
and "End" appears on the display panel for 3 seconds.
Note: To switch off the timer earlier, press any button.
Delay Shut-off
The delay shut-off time is ten minutes and cannot
be changed.
1.
Select fan speed setting.
Press "Timer" button for 3 seconds.
2.
Once this time has elapsed, the fan and lighting switch
off automatically. The display shows the message "End."
The delay shut-off feature can be interrupted at any time
by pressing one of the buttons.
7