AirStage UTY-LNHU Kurulum Kılavuzu - Sayfa 9
Uzaktan Kumanda AirStage UTY-LNHU için çevrimiçi göz atın veya pdf Kurulum Kılavuzu indirin. AirStage UTY-LNHU 10 sayfaları. Wireless
Sayfayı YazdırConfi rmation of function setting
(12)
Press the "TIMER set (+)" button.
"TIMER set (+)"
CORRECT :
WRONG :
■
Completion of function setting mode
(13)
Press and hold the "MANUAL/AUTO" button for 3 seconds.
IR RECEIVER
UNIT
* Each LED light brightness is darkening though the content of the display
doesn't change.
(14)
Press the "RESET" button.
After pressing the "RESET" button, please
set the custom code again if b,c,d setting.
* The function setting signal is not received after switched function setting
completion mode. (Pi Pi Pi Pi Pi)
* Press the "MANUAL/AUTO" button again for 3 sec to return to if required
to return the function setting mode.
■
Reconfi rmation of function setting
(15)
Press and hold the "FAN" and the "SET TEMP.
holding these 2 buttons, press the "RESET" button.
FAN
SET TEMP. ( )
RESET
(16) Function number to be
confi rmed is displayed.
Refer to (7).
Press the "TIMER set (-)"
"TIMER set (-)"
button.
PiPi
Pi
PiPiPiPiPi
PiPi
Pi
(3 sec)
Pi Pi Pi
MANUAL
AUTO
MANUAL AUTO
RESET
" buttons. Whilst
Function setting
mode display
Case1 : When setting number is 1 digit.
(Example) Function number : 30, Setting number : 01
0.5sec ON / 0.5sec OFF
OPERATION LAMP
(GREEN)
3 times
TIMER LAMP
(ORANGE)
0.5sec ON / 0.5sec OFF
FILTER LAMP
1 time
(RED)
(Phase1) : 12sec
Case2 : When setting number is 2 digits.
(Example) Function number : 26, Setting number : 31
0.5sec ON / 0.5sec OFF
OPERATION LAMP
2 times
(GREEN)
0.5sec ON / 0.5sec OFF
TIMER LAMP
(ORANGE)
0.5sec ON / 0.5sec OFF 0.5sec ON / 0.5sec OFF
FILTER LAMP
1 time
(RED)
(Phase1) : 12sec
■
Setting up each indoor unit
Repeat steps (1) through to (16). Steps (1) through to (5)
and (13) to (16) only need to carried out if the custom code
is different to the factory setting of "A".
■
Reset the power after setting up function of all indoor units
Important
•
If the reset is not performed, function cannot be read in normally.
•
After all the functions have been set, the circuit breaker needs to be
switched off for at least 2 minutes.
After the 2 minutes has passed, power can be restored.
•
The set function is stored in the PC board and will remain in memory even
when the power is turned off.
However setting function is effective after power reset.
Record the function set in the indoor unit on a label,
etc., and affi x the label to the unit so it can be used for
after-sales service operations.
* Number 0 setting will not indicate TIMER LAMP and FILTER LAMP.
* Once the "RESET" button is pressed on the remote controller, the
OPERATION MODE will be set in the "AUTO MODE".
Please adjust the OPERATION MODE to either "COOLING" or "HEATING"
before trying to operate the air conditioner.
* Note : If CUSTOM CODE is set to anything other than "A", the remote
control must be set accordingly to the INDOOR UNIT setting.
...
3 times
OFF
...
1 time
(Phase1) : 12sec
...
OFF
6 times
...
OFF
...
3 times
(Phase2) : 12sec
En-8